The SC Bobber

Bowers Bobbers now with a Swing Gate Vise that works great with all tubes!

Highlights:

• Precision Machined Aluminum Body with Blood Red Double Powder Coat Finish
  
• Matching Steel Swing Gate Vise that works great with all tubes!
• Deluxe Brass Hardware
• Plus Bowers Heavy Brass Wingnut for improved forward balance to keep the weight over your hand and balance out the pull of your clip cord

Specifications:

• Operating Range between 4-7 Volts
• Snappy Stroke
• Pushes any grouping with ease
• Great for Lining and Shading
• Needle on Bar or Cartridge Use
• Weighs 4 oz

Made in the USA

A few words From Joshua about this machine:
This is a very powerful and capable machine. It has real nice stroke characteristics, nice and snappy with the perfect amount of bog. The best machine if you're wanting to use one machine for lining, shading, or both. Designed for use with cartridges but is equally effective running needle and tube setup. It has a nice snappy powerful stroke that will drop in nice single pass lines with large or small groupings. As a shader, turn the voltage down to slow the speed and still have that punch to drop in solid color or blend with very low trauma.

Joshua Bowers Rubber Band Placement Diagram

The SC Bobber

Bowers Bobbers now with a Swing Gate Vise that works great with all tubes!

Highlights:

• Precision Machined Aluminum Body 
• Hand carved, patina’d and rubbed, then sealed up with a satin varnish to give it this incredible finish.. Paired with patina’d brass hardware. The perfect look..
• Blackened Steel Swing Gate Vise that works great with all tubes!
• Deluxe Brass Hardware
• Plus Bowers Heavy Brass Wingnut for improved forward balance to keep the weight over your hand and balance out the pull of your clip cord

Specifications:

• Operating Range between 4-7 Volts
• Snappy Stroke
• Pushes any grouping with ease
• Great for Lining and Shading
• Needle on Bar or Cartridge Use
• Weighs 4 oz

Made in the USA

A few words From Joshua about this machine:
This is a very powerful and capable machine. It has real nice stroke characteristics, nice and snappy with the perfect amount of bog. The best machine if you're wanting to use one machine for lining, shading, or both. Designed for use with cartridges but is equally effective running needle and tube setup. It has a nice snappy powerful stroke that will drop in nice single pass lines with large or small groupings. As a shader, turn the voltage down to slow the speed and still have that punch to drop in solid color or blend with very low trauma.

Joshua Bowers Rubber Band Placement Diagram

Joshua Bowers High-Jack

The High-Jack attaches to your workstation magnetically and plugs in to the "machine" port on your power supply effectively moving your clip cord jack 5 feet into the air. This is the ideal position for your clip cord to hang from to keep it off the floor and free from rubbing, tugging, and snagging as you work.

• No more rolling over your cord with your chair
• Keep your cord off the floor
• Reduces the weight hanging off the back of the machine
• Reduces tugs and snags as you tattoo
• Extends the life of your clipcord

A few words from Joshua about The High-Jack:

"The High-Jack is a product I developed to make my clipcord drape and move more easily. The High-Jack magnetically attaches to your work station and plugs in to the Machine port on your power supply. Your clip cord then plugs in to the High-Jack, effectively lifting the clipcord jack 5 feet in to the air. This allows the cord to drape naturally from above you, doesn’t rub on the floor, doesn’t snag across your lap and it takes weight off of the back of the machine easing hand fatigue greatly.

The High-Jack Switch has all the great features of the basic High-Jack with the great new feature of having a switch box at the end to be able to toggle back and forth between two cords. This is a great feature for people using multiple cord types or just want two cords connected so they don’t have to switch cords back and forth. The toggle move from side to side selecting which cord is powered with off in the middle, so you can run on constant and turn your machine off at the High-Jack.

I have been using this product for over a year now, along with the rest of my shop. We were originally just testing them out but I speak for me and the rest of the shop when I say that we can’t imagine tattooing without them now."

Joshua Bowers Repairable Clip Cord

COMES WITH A TOOL KIT WITH ALL THE TOOLS YOU NEED TO REPAIR IT, including instructions and extra parts. Designed with function and maintenance in mind, this lightweight clip cord can be repaired quickly and easily! Never find yourself in a situation without a functioning clipboard and no options again.

Highlights:

• Light weight non-stick cord material
• Brass leads that are replaceable and easily modified to suit your machines or how you like your cord to lay
• Long life spring that can be replaced, or repaired
• Wires can be removed from lugs to repair shorts that happen from movement.
• 6 foot length
• Very lightweight at a mere 2.45 ounces
• Limited 1 Year Warranty covers product defects and not every day wear and tear.
  

Made in the USA

Some words from Bowers on why he made these clip cords:

A couple years ago I designed this clip cord and built one for myself. The design came from being frustrated with the options that were on the market. When I designed these clip cords I had a list of demands.
-This cord HAD to be repairable, quickly and easily.
-lightweight
-no-stick, flexible cord
-brass or copper leads
Every part of the clip cord end can be replaced or repaired quickly and easily. Even comes with the parts and tools to do it! You will not be left struggling with a short in your cord, no backup and rummaging around looking for your best broken cord to finish or do the tattoo. The cord is a matte non stick material that glides smoothly along surfaces, it is NOT a 5 lb clip cord you’re hooking up to 3 oz. machine, the brass leads will not groove your binding posts nearly as fast as the standard steel leads found on most clip cords. I’m excited about this new product and to able to finally share it with all of you.

Limited Edition version of the Joshua Bowers Repairable Clip Cord in Pink with Black Clips!

COMES WITH A TOOL KIT WITH ALL THE TOOLS YOU NEED TO REPAIR IT, including instructions and extra parts. Designed with function and maintenance in mind, this lightweight clip cord can be repaired quickly and easily! Never find yourself in a situation without a functioning clipboard and no options again.

Highlights:

• Light weight non-stick cord material
• Blackened Stainless Steel leads that are replaceable and easily modified to suit your machines or how you like your cord to lay
• Long life spring that can be replaced, or repaired
• Wires can be removed from lugs to repair shorts that happen from movement.
• 6 or 8 foot length
• Very lightweight at a mere 2.45 ounces
• Limited 1 Year Warranty covers product defects and not every day wear and tear.
  

Made in the USA

Some words from Bowers on why he made these clip cords:

A couple years ago I designed this clip cord and built one for myself. The design came from being frustrated with the options that were on the market. When I designed these clip cords I had a list of demands:
-This cord HAD to be repairable, quickly and easily.
-lightweight
-no-stick, flexible cord
-brass or copper leads
Every part of the clip cord end can be replaced or repaired quickly and easily. Even comes with the parts and tools to do it! You will not be left struggling with a short in your cord, no backup and rummaging around looking for your best broken cord to finish or do the tattoo. The cord is a matte nonstick material that glides smoothly along surfaces, it is NOT a 5 lb clip cord you’re hooking up to 3 oz. machine, the brass leads will not groove your binding posts nearly as fast as the standard steel leads found on most clip cords. I’m excited about this new product and to able to finally share it with all of you.

Joshua Bowers Steeldriver Rotary

 This machine has proven to be an incredibly capable liner and shader with cartridges and needle tube setup.

Highlights:

• Steel body with Swing Gate Vise
• Forward weighted machine for better balance over the hand
• Blackened Finish
• Deluxe Polished Brass Hardware
• Bowers Brass Weighted Wingnut

Specifications:

• Designed for both lining and shading, with the bonus of being a great stipple shader as well
• Adjustable yoke for both slow, punchy strokes or a tighter, snappy stroke
• Suitable for both large and small groupings
• Weighs roughly 5 ounces...but 1 ounce of that is the weighted thumbscrew which can be replaced if interested in shedding some weight

Made in the USA

A few words from Joshua about this machine:

"The Steeldriver is an incredibly versatile and effective machine. Snappy off the tip with a great bog. A very intuitive coil like hit. Great for lining and shading with needle on bar and cartridges too. The Steeldriver’s special yoke allows the stroke to be adjustable as well. The spring tension in the yoke is adjustable so you can adjust the hit to be more slappy and hard, or tighter and softer. So fine tune your hit to suite your preference without negatively affecting its tune. This Steeldriver lines and shades like an absolute dream."

Joshua Bowers Micro-Liner Rotary Tattoo Machine

Now with a Swing Gate Vise that works great with all tubes! 

Highlights:

• 3 Piece Bolt-Up Body
• Blackened Steel Vise and Spring Shelf
• Anodized Black Aluminum Body
• Deluxe Brass Hardware
• Now with Bowers Brass Weighted Wingnut for better balance

Specifications:

• Runs best between 6-7 Volts
• Pushes any grouping with ease
• Weighs 3.65 oz

Made in the USA

A few words from Joshua about this machine:

"This machine is designed, built and tuned to run like a coil machine. The tuning is in the frame geometry and setup so there's no knobs or settings to fall out of adjustment. Ready to tattoo out of the box. Light, but not too light. Very punchy and snappy on the tip of the stroke and backs off slightly in the middle of the stroke. Great for sculpting fine finesse lines ran off the needle tips and also great for burying a large grouping liner and pulling a solid single pass line quickly."
Joshua Bowers Micro Liner Care Instructions

Joshua Bowers Rubber Band Placement Diagram

Joshua Bowers 2 Stroke Direct Drive+

Now with a Swing Gate Vise that works great with all tubes!

Two machines in one! Easily change from a standard solid hitting Direct Drive to a Rotary with give simply by changing the polarity / flipping your clip cord connection.

Highlights:

• 3 Piece Bolt-Up Body
• Blackened Steel Swing Gate Vise that works great with all tubes!
  
• Anodized Black Aluminum Motor Cover and Frame
  
• Deluxe Brass Hardware
• Now with Bowers Brass Weighted Wingnut to balance Clip Cord Pull
  

Specifications:

• Runs best between 3-6 Volts
• 5mm Stroke
• Pushes any grouping with ease...big stuff, small stuff, no problem
  
• Good with Carts or Needle on Bar
• Lining, Color Packing, Stippling, B&G....it does it all
• Weighs 4.65 oz

A few words from Joshua about this machine:

"The time is finally here to introduce my new direct drive project that I’ve been developing with @workhorseirons . I’d like to introduce the 2 Stroke. I called it the 2 Stroke because it has the unique ability among direct drives as having two very unique and different stroke characteristics in one machine. When the machine is hooked up with the positive to the top binding post the 2 Stroke is a killer, snappy super capable long stroke direct drive. Flip the clip cord so the positive is on bottom, and it changes the stroke completely. The 2 Stroke has a torsional swing arm in the cam that reacts to the resistance of the skin. On the “give” setting the needles hit the skin softer and less abrasive but the best part is that unlike typical “give” mechanisms the give on the 2 Stroke doesn’t control needle depth. The needles will hit the skin with less force but still penetrate the skin the same depth as if no give was used. This ensures that all ink is deposited in the depth of retention, needle depth is more predictable, and tattoos heal more solid on all the different types of skin."

Joshua Bowers Big Can Rotary Tattoo Machine

Highlights:

• 3 Piece Bolt-Up Body
• Black Zinc Finish
• Deluxe Brass Hardware
• Now with Bowers Brass Weighted Wingnut for better balance

Specifications:

• Runs best around 7-7.6 Volts
• Pushes any grouping with ease
• Weighs 4.75 oz

Made in the USA

A few words from Joshua about this machine: 
Super smooth and consistent machine. Powerful through the whole stroke but designed to back off slightly in the middle and back end of the stroke to prevent overworking the skin. Super versatile, great for color saturation, blending, and even black and gray. Plenty of stroke to hang out for nice traditional whips or back it up and increase the voltage for smooth saturation. Has a penetrating stroke down to 4 volts which is great for stippling.
Joshua Bowers Big Can Care Instructions

Joshua Bowers Rubber Band Placement Diagram

Joshua Bowers SC Bobber

Now with a Swing Gate Vise that works great with all tubes!

Highlights:

• Precision Machined Aluminum Body with Durable Black Anodize Finish
  
• Blackened Steel Swing Gate Vise that works great with all tubes!
• Deluxe Brass Hardware
• Plus Bowers Heavy Brass Wingnut for improved forward balance to keep the weight over your hand and balance out the pull of your clip cord
  

Specifications:

• Operating Range between 4-7 Volts
• Snappy Stroke
• Pushes any grouping with ease
• Great for Lining and Shading
• Designed for use with cartridges but is equally effective running needle and tube setup.
• Weighs 4 oz

Made in the USA

A few words from Joshua about this machine:
This is a very powerful and capable machine. It has real nice stroke characteristics, nice and snappy with the perfect amount of bog. The best machine if you're wanting to use one machine for lining, shading, or both. Designed for use with cartridges but is equally effective running needle and tube setup. It has a nice snappy powerful stroke that will drop in nice single pass lines with large or small groupings. As a shader, turn the voltage down to slow the speed and still have that punch to drop in solid color or blend with very low trauma.

Joshua Bowers Rubber Band Placement Diagram

Joshua Bowers SC Bobber

Now with a Swing Gate Vise that works great with all tubes!

Highlights:

• Precision Machined Aluminum Body with Custom Sparkle Chameleon Blue Rust Powder Coat Finish
  
• Blackened Steel Swing Gate Vise that works great with all tubes!
• Deluxe Brass Hardware
• Plus Bowers Heavy Brass Wingnut for improved forward balance to keep the weight over your hand and balance out the pull of your clip cord
  

Specifications:

• Operating Range between 4-7 Volts
• Snappy Stroke
• Pushes any grouping with ease
• Great for Lining and Shading
• Needle on Bar or Cartridge Use
• Weighs 4 oz

Made in the USA

A few words from Joshua about this machine:
This is a very powerful and capable machine. It has real nice stroke characteristics, nice and snappy with the perfect amount of bog. The best machine if you're wanting to use one machine for lining, shading, or both. Designed for use with cartridges but is equally effective running needle and tube setup. It has a nice snappy powerful stroke that will drop in nice single pass lines with large or small groupings. As a shader, turn the voltage down to slow the speed and still have that punch to drop in solid color or blend with very low trauma.
Joshua Bowers Micro Liner Care Instructions

Joshua Bowers Rubber Band Placement Diagram

Bowers Bobbers now with a Swing Gate Vise that works great with all tubes!

Highlights:

• Precision Machined Aluminum Body with Seafoam Powder Coat Finish
  
• Blackened Steel Swing Gate Vise that works great with all tubes!
• Deluxe Brass Hardware
• Plus Bowers Heavy Brass Wingnut for improved forward balance to keep the weight over your hand and balance out the pull of your clip cord

Specifications:

• Operating Range between 4-7 Volts
• Snappy Stroke
• Pushes any grouping with ease
• Great for Lining and Shading
• Needle on Bar or Cartridge Use
• Weighs 4 oz

Made in the USA

A few words From Joshua about this machine:
This is a very powerful and capable machine. It has real nice stroke characteristics, nice and snappy with the perfect amount of bog. The best machine if you're wanting to use one machine for lining, shading, or both. Designed for use with cartridges but is equally effective running needle and tube setup. It has a nice snappy powerful stroke that will drop in nice single pass lines with large or small groupings. As a shader, turn the voltage down to slow the speed and still have that punch to drop in solid color or blend with very low trauma.

Joshua Bowers Rubber Band Placement Diagram