NEW Dan Kubin V3/24 Sidewinder!

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

RCA Specifications:

• RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
• This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
• This will also work good with a right-angle RCA cord.
• Clip Cord option still works, it is just wired backwards.
• The position of the battery makes the machine’s balance point much more forward, like a pen.

Machine Specs:

• HD Red Apple Powder Coated Brass Frame with Nickel Plated Hardware and Motor Cover
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.

NEW Dan Kubin V3/24 Sidewinder!

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

Machine Specs:

• HD Green Apple Powder Coated Brass Frame with Nickel Plated Hardware and Motor Cover
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.

December is an expensive month, as a thanks for your continued business and support all items in this category are 20% OFF the lowest listed price!

20% OFF DISCOUNT APPLIES IN CART!  No Code Needed.

Order by December 20th with appropriate shipping method to receive by Christmas!

Workhorse Model 6 Liner

Formerly built by Marv Lerning, this is an updated and modernized version of Marv's 6 Liner inspired by the Waters Model 6 Frame. Now with updated geometry for more power and efficiency, plus swing gate vise added to guarantee ease of use with any and all tubes. 

We are stoked to release this new Workhorse Model built in house by our highly trained and knowledgeable machine techs. Bringing us back to our roots with an affordable base model machine made with shared parts and technology to reduce costs. We offer lots of limited and custom high-end machines these days and wanted to release a new base model option at base model pricing.

Specs:

• Full Size Frame milled in house from a solid block of Ductile Iron
• Plateau Green x Pink Powder Coat Finish
• Deluxe Workhorse Hardware with Black Oxide Finish
• Swing Gate Steel Vise
• Custom 6 Wrap 1.25" Coils
• High End Specialty Steel Springs
• Solid Copper Contact with Allen Key Insert
• Reverse Rear Binder Setup with frame ground on coil deck
• Long Stroke with a solid hit great for 5s to 14s
  
• Medium Speed, running around 135-140 unloaded @ 6.5 Volts
• 6.5 Ounce Weight
• Made in the USA

December is an expensive month, as a thanks for your continued business and support all items in this category are 20% OFF the lowest listed price!

20% OFF DISCOUNT APPLIES IN CART!  No Code Needed.

Order by December 20th with appropriate shipping method to receive by Christmas!

Mike Pike PMA Direct Drive Rotary!

After a couple years of minor tweaks and lots of testing, the new Mike Pike Direct Drive Rotary is finally ready! Not necessarily a reinvention of the wheel, but applying his years of knowledge tattooing and building rotary machines, Pike dialed in these Direct Drives and simply made a great running Rotary.

Built using only the finest components to produce a great all around direct drive that is smooth running, consistent, and rock solid for years of trouble free use. Made with powerful high end motors, an adjustable Cam to accommodate any stroke, vertical swing gate vise guarantee to grip tubes with no issue, and top of the line aluminum that is both lightweight and strong enough to stand the test of time.

- Limited Edition Run of Illusion Pink Powder Coat with Gold Disco Clear Gold and Heavy HD Black Bodies. PLUS 24k Gold Plated Motor Cap, Swing Gate Vise, and Nickel Plated Hardware.
-High-grade Aluminum body precision milled frames and components
- Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
- Comfortable and well balanced with a vertical swing gate tube vice that will bite and hold all disposable and stainless tubes
- Adjustable Brass Cam with PMA reference marks to help keep track of stroke settings and adjustments. Simply loosen the cam set screw, pull out the inner cam and insert it back in at either a shorter or longer setting to change the stroke quick and easy
- Pushes up to 25 mag and up to 18 Rounds no problem, Needle on Bar or Cartridges
- Runs best anywhere between 5 and 10 volts depending on what you are pushing and how you are tattooing
- Lightweight weighing in at a mere 4.5 oz
- Clipcord Connection

Made with love in the USA by Mike Pike and his 40+ years of experience tattooing and building machines.

Thanks and enjoy,
Mike Pike