Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!
Now with more versatility and ease of hit adjustment throughout the tattoo. It is more ergonomic, more reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary.
Highlights:
Brass Frame with Pink HD Finish
Numbered upstroke wheel (same as the V3r). The higher the number, the harder it will hit. *Please use common sense & not run it on high volts with a high setting on the upstroke wheel.
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive which is the nature of a cartridge.
Specifications:
Normal operating range: 5.3 - 6 volts for lining, 4 - 5.5 volts for shading.
Excellent for fine line, black and grey, color packing with any size mag.
Can drive 14 liners, if you prefer to “set the needle into the skin”
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive, which is the nature of a cartridge.
Weight: 5 oz
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Mojobox go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Mojobox are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Highlights:
Steel Frame with HD Light Pink Powder Coat Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Setup / Specifications:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components! Sterilants are corrosive and will damage your machine if used carelessly.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All MCI go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current MCI are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
The main goal for this batch is for simple tuning, but with the option to dial it precisely for those who know how they want their machine to run. Considered by some to be the most revolutionary Sidewinder yet.
The v7.5 Sidewinder has the unique ability to allow users to adjust stroke length and hit independently. This means you can keep the stroke that works for you while playing with needle groupings, style, and skin types.
Highlights:
Polished Nickle plated frame with Black side plating
Deluxe Blackened Hardware
Impact screw and stroke length are now adjusted with the 1.5mm Allen key provided with the machine.
Straight angle on drive spring shelf on the armature bar, allowing for a more effortless and graceful hit.
More prominent timing marks on the side plate for the impact pin. (for advanced tuning/stroke adjustment, this helps with being more intuitive)
Crisp and clean acoustics, slightly quieter than other sidewinder models
Side locking screw is positioned to secure the impact screw most effectively
Specifications:
Forward, low and balanced weight of 6.2 oz
Recommended voltage range: 4 - 6.5
Great in the lower volt range for shading to color packing, fine line and stippled whip shading techniques.
It has 5 stroke positions ranging from 3.5-4mm. While tattooing, hit is controlled with adjustable return spring tension. If you want a softer hitting machine, you don’t have to compromise the stroke length.
The main goal for this batch is for simple tuning, but with the option to dial it precisely for those who know how they want their machine to run. Considered by some to be the most revolutionary Sidewinder yet.
The v7.5 Sidewinder has the unique ability to allow users to adjust stroke length and hit independently. This means you can keep the stroke that works for you while playing with needle groupings, style, and skin types.
Highlights:
Deluxe 24k Gold plated frame with Black side plating
Deluxe Blackened Hardware
Impact screw and stroke length are now adjusted with the 1.5mm Allen key provided with the machine.
Straight angle on drive spring shelf on the armature bar, allowing for a more effortless and graceful hit.
More prominent timing marks on the side plate for the impact pin. (for advanced tuning/stroke adjustment, this helps with being more intuitive)
Crisp and clean acoustics, slightly quieter than other sidewinder models
Side locking screw is positioned to secure the impact screw most effectively
Specifications:
Forward, low and balanced weight of 6.2 oz
Recommended voltage range: 4 - 6.5
Great in the lower volt range for shading to color packing, fine line and stippled whip shading techniques.
It has 5 stroke positions ranging from 3.5-4mm. While tattooing, hit is controlled with adjustable return spring tension. If you want a softer hitting machine, you don’t have to compromise the stroke length.
Dan Kubin Sidewinder 46er - Antique Nickel x Black
Regular price$910.00 USD
Dan Kubin's Newest Sidewinder, the V46er!
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. Its number one purpose is as a strong, precise, off the tip liner; though it has proven to be much more capable.
Highlights:
Antique Nickel Plated Frame with Black Motor Cover and Blackened Deluxe DK Components
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
Beautiful brass armature bar, perfectly balanced for a strong, confident, and consistent hit.
O-ring groove in the bar allows for a more silent option (though will reduce performance as well)
Reliable Mabuchi motor. -because they run forever without losing consistency.
Specifications:
Weighs 6 oz
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
Polarity: Positive up - spins motor clockwise - slaps harder, ideal for large grouping liners. Positive down - spins motor counterclockwise -slightly passive hit, ideal for shading and fine line
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Highlights:
Steel Frame with durable Antique Nickel Plated Finish
24k Gold Plated Hardware
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Setup / Specifications:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components! Sterilants are corrosive and will damage your machine if used carelessly.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All MCI go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current MCI are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Highlights:
Steel Frame with durable Rubbed Bronze Plated Finish
24k Gold Plated Hardware
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Setup / Specifications:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components! Sterilants are corrosive and will damage your machine if used carelessly.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All MCI go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current MCI are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Dan Kubin Sidewinder 46er - Verdigris x Black RCA + Clip Cord
Regular price$965.00 USD
Dan Kubin's V46er Sidewinder
New Limited Run of Light Green Verdigris! Much greener than the standard Verdigris. *
* Finish may vary
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. Its number one purpose is as a strong, precise, off the tip liner; though it has proven to be much more capable.
Highlights:
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
Reliable Mabuchi motor. -because they run forever without losing consistency.
Specifications:
Weights 6oz
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (Keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards (Positive Down for Harder Hit)
The position of the battery makes the machine’s balance point much more forward, like a pen.
NEW RCA / Clip cord version with straight up battery position
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website..
Dan Kubin Sidewinder 46er - Antique Nickel x Black RCA + Clip Cord
Regular price$910.00 USD
Dan Kubin's Newest Sidewinder, the V46er!
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. Its number one purpose is as a strong, precise, off the tip liner; though it has proven to be much more capable.
Highlights:
Antique Nickel Plated Frame and Matching Motor Cover with Blackened Deluxe DK Components.
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
Beautiful brass armature bar, perfectly balanced for a strong, confident, and consistent hit.
O-ring groove in the bar allows for a more silent option (though will reduce performance as well)
Reliable Mabuchi motor. -because they run forever without losing consistency.
Specifications:
Weighs 6 oz
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards (Positive Down for Harder Hit)
The position of the battery makes the machine’s balance point much more forward, like a pen.
NEW RCA / Clip cord version with straight up battery position
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
The main goal for this batch is for simple tuning, but with the option to dial it precisely for those who know how they want their machine to run. Considered by some to be the most revolutionary Sidewinder yet.
The v7.5 Sidewinder has the unique ability to allow users to adjust stroke length and hit independently. This means you can keep the stroke that works for you while playing with needle groupings, style, and skin types.
Highlights:
Deluxe 24k Gold plated frame with Black side plating
Deluxe 24k Gold Hardware
Impact screw and stroke length are now adjusted with the 1.5mm Allen key provided with the machine.
Straight angle on drive spring shelf on the armature bar, allowing for a more effortless and graceful hit.
More prominent timing marks on the side plate for the impact pin. (for advanced tuning/stroke adjustment, this helps with being more intuitive)
Crisp and clean acoustics, slightly quieter than other sidewinder models
Side locking screw is positioned to secure the impact screw most effectively
Specifications:
Forward, low and balanced weight of 6.2 oz
Recommended voltage range: 4 - 6.5
Great in the lower volt range for shading to color packing, fine line and stippled whip shading techniques.
It has 5 stroke positions ranging from 3.5-4mm. While tattooing, hit is controlled with adjustable return spring tension. If you want a softer hitting machine, you don’t have to compromise the stroke length.
Dan Kubin Sidewinder 46er - Pink x Pink RCA + Clip Cord
Regular price$935.00 USD
Dan Kubin's Newest Sidewinder, the V46er with RCA + Clip Cord!
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. Its number one purpose is as a strong, precise, off the tip liner; though it has proven to be much more capable.
Highlights:
Durable anodized finish that helps prevent corrosion.
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
Beautiful brass armature bar, perfectly balanced for a strong, confident, and consistent hit.
O-ring groove in the bar allows for a more silent option (though will reduce performance as well)
Reliable Mabuchi motor. -because they run forever without losing consistency.
Specifications:
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards (Positive Down for Harder Hit)
The position of the battery makes the machine’s balance point much more forward, like a pen.
NEW RCA / Clip cord version with straight up battery position
Made in the USA!
All DK Machines sold by Workhorse are engineered, designed, and tested by Dan, milled in his most trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Limited Pike x Rogers Slider Rotary - Watermelon GOOD OMEN Cobra
Regular price$495.00 USD
Limited Mike Pike x Cory Rogers Linear Rotary!
Special Edition with artwork by Julia Campione of Good Omen Tattoo!
🔥Watermelon Flavored GOOD OMEN COBRA🔥
Built and designed by Cory Rogers and Mike Pike, these collaborative linear rotary machines are smooth running, consistent, and built with only the finest components to ensure years of problem free use.
Highlights:
Precision milled high-grade Aerospace Aluminum body
Custom Pink Hard Anodized Components and Bright Green Frame
Custom Good Omen Cobra Etching by Julia Campione
Blackened Deluxe Hardware
Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
Forward facing wingnut that won't ride your hand or get in your way
Specifications:
4 mm stroke that works great for color packing, shading and also large groupings lining
Pushes 5 to 49 mag and 9 to 18 Rounds no problem
Runs best anywhere between 5 and 10 volts
Most are lining between 8-10 Volts for larger groupings, 5-9 volts for color packing and B&G work
Great with Needle on Bar or Cartridges
Lightweight weighing in at a mere 4.5 oz
Made with love in the USA
Thanks and enjoy, Mike & Cory
Workhorse Irons
Dan Kubin Sidewinder 46er - Pink x Gold RCA + Clip Cord
Regular price$1,030.00 USD
Dan Kubin's Newest Sidewinder, the V46er with RCA + Clip Cord Connection!
New Limited Run of HD Pink Powder Coated Brass V46er with 24k Gold Plated Hardware and RCA + Clip Cord connection for all the options!
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. Its number one purpose is as a strong, precise, off the tip liner; though it has proven to be much more capable.
Highlights:
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
Reliable Mabuchi motor. -because they run forever without losing consistency.
Specifications:
Weights 6oz
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (Keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards (Positive Down for Harder Hit)
The position of the battery makes the machine’s balance point much more forward, like a pen.
NEW RCA / Clip cord version with straight up battery position
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website..
Dan Kubin Mojobox V2.2 - Black x Gold Featherweight
Regular price$850.00 USD
Dan Kubin Mojobox V2.2
Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!
Now with more versatility and ease of hit adjustment. It is ergonomic, reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary. The Mojobox is a great deliberate shader and can also be tuned for your lining needs.
Highlights:
Featherweight Aluminum Frame with Black HD Anodized Finish
24k Gold Plated Parts
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.
Specifications:
Normal operating range: 5.3 - 6 volts for lining, 4 - 5.5 volts for shading. It is not recommended to exceed 7.
Excellent for fine line, black and grey, color packing.
Can drive 14 liner
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive, which is the nature of a cartridge.
Limited Pike x Rogers Slider Rotary -Purple x Green GOOD OMEN Cobra
Regular price$495.00 USD
Special Edition with artwork by Julia Campione of Good Omen Tattoo!
Limited Mike Pike x Cory Rogers Linear Rotary!
🔥Purple x Green GOOD OMEN COBRA🔥
Built and designed by Cory Rogers and Mike Pike, these collaborative linear rotary machines are smooth running, consistent, and built with only the finest components to ensure years of problem free use.
Here are the specifics:
Precision milled high-grade Aerospace Aluminum body
Custom Purple Hard Anodized Frame and Green Anodized Parts
Polished Nickel Plated Hardware
Custom Good Omen Cobra Etching by Julia Campione
Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
Forward facing wingnut that won't ride your hand or get in your way
4 mm stroke that works great for color packing, shading and also large groupings lining
Pushes 5 to 49 mag and 9 to 18 Rounds no problem
Runs best anywhere between 5 and 10 volts
Most are lining between 8-10 Volts for larger groupings, 5-9 volts for color packing and B&G work
Great with Needle on Bar or Cartridges
Lightweight weighing in at a mere 4.5 oz
Made with love in the USA by real tattooers Mike Pike and Cory Rogers.
