*BLACK FRIDAY Special Edition run at special pricing!

Aaron Cain Roundback Shader Ver 2.0, based on the OG Sand Cast Iron Roundbacks Aaron did years ago, now CNC cut with a few improvements!

- New CNC Cut Iron Frame
- 2 Tone Distressed Green Powder Coat Finish
- Standard Workhorse Blackened Steel Hardware
- 1" 8 Wrap Custom Dyed Money Coils
- Long Stroke with a Medium Hit
- Running 100-105 Hz @ 6.5 V unloaded
- Pushing 5's to 11's no problem
- Weighs 6.45 Ounces
- MADE IN THE USA

*BLACK FRIDAY Special Edition run at special pricing!

Aaron Cain Roundback Liner Ver 2.0, based on the OG Sand Cast Iron Roundbacks Aaron did years ago, now CNC cut with a few improvements!

- CNC Cut Iron Mini Frames
- 2 Tone Distressed Green Powder Coat Finish
- Standard Workhorse Blackened Steel Hardware
- 1" 8 Wrap Custom Dyed Money Coils
- Quick with a Medium Stroke and a Solid Medium Hit
- Running 145-150 Hz @ 6.5 V unloaded
- Pushing 3's to 7's with ease, turn up volts to push 9s
- Weighs 6.45 Ounces
- MADE IN THE USA

*BLACK FRIDAY Special Edition run at special pricing!

*Limited batch of these special edition Bowers' Bobbers setup to push nearly any grouping for lining and shading!

Now with a Swing Gate Vise that works great with all tubes!

A Few Words From Joshua about this machine:
This is a very powerful and capable machine. It has real nice stroke characteristics, nice and snappy with the perfect amount of bog. The best machine if you're wanting to use one machine for lining, shading, or both. Designed for use with cartridges but is equally effective running needle and tube setup. It has a nice snappy powerful stroke that will drop in nice single pass lines with large or small groupings. As a shader, turn the voltage down to slow the speed and still have that punch to drop in solid color or blend with very low trauma.

Joshua Bowers SC Bobber Specs:

• Precision Machined Aluminum Body with 24k Gold Plated Finish
  
• Blackened Steel Swing Gate Vise that works great with all tubes!
• Deluxe Brass Hardware
• Plus Bowers Heavy Brass Wingnut for improved forward balance to keep the weight over your hand and balance out the pull of your clip cord
  
• Weighing in at a mere 4 oz!
• Operating Range between 4-7 Volts
• Snappy Stroke
• Pushes any grouping with ease
• Great for Lining and Shading
• Needle on Bar or Cartridge Use

Joshua Bowers Micro Liner Care Instructions

Joshua Bowers Rubber Band Placement Diagram

*BLACK FRIDAY Special Edition run at special pricing! New V2 GDR Limited Edition Run with Wild Style Powder Coat Finish!

This is the new updated and improved version of the DK x AC Ghost Dog Revival. V2 features an upgraded slide vise guaranteed to easily work with any and all tubes, an opened up geometry for better function, performance, and power. Everything else is the same, just dialed in a little more to make it a little better :)

"Since working with Workhorse Irons, I have been given the opportunity to remaster my Revival machine, but being able to merge it into the platform of Adam Ciferri’s Ghostdog.

Thanks - Dan.

Dan Kubin X Adam Ciferri Ghost Dog Revival V2 Machine Specs:

• CNC Iron Frame designed in collaboration by Dan Kubin and Adam Ciferri
• Hinge / Compression machine functionality eliminating any rear spring issues or breakage
• Machine comes setup for use as a slow or medium speed Liner. Also works well as a quick Shader if you turn down the volts a little. To easily change to a slow and punchy color packer, simply remove the backer spring under the front spring.
• Tuned for all-day, every-day street shop and/or custom tattooing
•  Medium speed with enough hit to easily push 3 to 18 Rounds and up to 49 mag
  
• Runs 125-130 Hz @ 6 Volts Unloaded, crank up to 8-10 Volts for large groupings
• CNC Cut Iron with the highest precision and care
• Mini-Size frame with Custom AC x DK 1" Keg Coil for a larger range and less amperage
• HD Black x Hot Pink x Illusion Purple x Lime Green Powder Coat Finish
• Deluxe DK Blackened Hardware and Specialty Spring
• Weighs 6 oz
• MADE IN THE USA

Machine Setup:

• Standard Needle on Bar: standard coil machine set up. Work well with our Thick Rubber Bands and Dan's Perfect Nipples, but also work with standard nipples/grommets.
• Cartridges: possible, but not highly recommended.

*BLACK FRIDAY Special Edition run at special pricing!

Mike Pike PMA Direct Drive Rotary!

After a couple years of minor tweaks and lots of testing, the new Mike Pike Direct Drive Rotary is finally ready! Not necessarily a reinvention of the wheel, but applying his years of knowledge tattooing and building rotary machines, Pike dialed in these Direct Drives and simply made a great running Rotary.

Built using only the finest components to produce a great all around direct drive that is smooth running, consistent, and rock solid for years of trouble free use. Made with powerful high end motors, an adjustable Cam to accommodate any stroke, vertical swing gate vise guarantee to grip tubes with no issue, and top of the line aluminum that is both lightweight and strong enough to stand the test of time.

- Limited Edition Run of Olive Green Anodized Bodies with 24k Gold Plated Motor Cap, Swing Gate Vise, and Hardware.
-High-grade Aluminum body precision milled frames and components
- Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
- Comfortable and well balanced with a vertical swing gate tube vice that will bite and hold all disposable and stainless tubes
- Adjustable Brass Cam with PMA reference marks to help keep track of stroke settings and adjustments. Simply loosen the cam set screw, pull out the inner cam and insert it back in at either a shorter or longer setting to change the stroke quick and easy
- Pushes up to 25 mag and up to 18 Rounds no problem, Needle on Bar or Cartridges
- Runs best anywhere between 5 and 10 volts depending on what you are pushing and how you are tattooing
- Lightweight weighing in at a mere 4.5 oz
- Clipcord Connection

Made with love in the USA by Mike Pike and his 40+ years of experience tattooing and building machines.

Thanks and enjoy,
Mike Pike