Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Specs:
Steel Frame with 24k Gold Plated Frame and Hardware
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
Limited Pike x Rogers Slider Rotary -Green x Gold GOOD OMEN Cobra
Regular price$495.00 USD
Special Edition with artwork by Julia Campione of Good Omen Tattoo!
Limited Mike Pike x Cory Rogers Linear Rotary!
🔥Green x Gold GOOD OMEN COBRA🔥
Built and designed by Cory Rogers and Mike Pike, these collaborative linear rotary machines are smooth running, consistent, and built with only the finest components to ensure years of problem free use.
Here are the specifics:
Precision milled high-grade Aerospace Aluminum body
Custom Green Hard Anodized Components and Gold Hard Anodized Frame
Custom Good Omen Cobra Etching by Julia Campione
Polished Nickel Plated Deluxe Hardware
Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
Forward facing wingnut that won't ride your hand or get in your way
4 mm stroke that works great for color packing, shading and also large groupings lining
Pushes 5 to 49 mag and 9 to 18 Rounds no problem
Runs best anywhere between 5 and 10 volts
Most are lining between 8-10 Volts for larger groupings, 5-9 volts for color packing and B&G work
Great with Needle on Bar or Cartridges
Lightweight weighing in at a mere 4.5 oz
Made with love in the USA by real tattooers Mike Pike and Cory Rogers.
Thanks and enjoy, Mike & Cory
Workhorse Irons
Dan Kubin Sidewinder 46er - White x Gold
Regular price$1,100.00 USD
Dan Kubin's Newest Sidewinder, the V46er!
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. It's number one purpose is as a strong, precise, off the tip liner; though It has proven to be much more capable.
Rustic beauty at its finest! Verde patina copper with a durable baked-on lacquer protective coating. Finish may vary as this is a very unique custom patina.
WHITE HD POWDER COAT FRAME + 24k Gold Plated Gold Parts and Hardware
Features include:
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
24k Gold Plated Beautiful brass armature bar, perfectly balanced for a strong, confident, and consistent hit.
O-ring groove in the bar allows for a more silent option (though will reduce performance as well)
Reliable Mabuchi motor. -because they run forever without losing consistency.
Weight:
Standard (brass frame construction): 6oz
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
Polarity: Positive up - spins motor clockwise - slaps harder, ideal for large grouping liners
Positive down - spins motor counterclockwise -slightly passive hit, ideal for shading and fine line
The 46er is a culmination of my versions 4-6 Sidewinders, remastered and enhanced to perfection. This machine features a very large stroke adjustment range that can suite single needle work, all the way up to the largest liners and mag shaders.
This machine is very strong off the tip with a great follow-through. It's number one purpose is as a strong, precise, off the tip liner; though It has proven to be much more capable.
WHITE HD POWDER COATED FINISH 🖤
Features include:
Wider springs for more durability.
Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
Smooth, easy clamping tube vice.
Forward weight distribution for better ergonomics.
Beautiful brass armature bar, perfectly balanced for a strong, confident, and consistent hit.
O-ring groove in the bar allows for a more silent option (though will reduce performance as well)
Reliable Mabuchi motor. -because they run forever without losing consistency.
Weight:
Standard (brass frame construction): 6oz
Recommended voltage range: 4 - 6.5 volts
Approximate stroke range: 2 - 4mm (keep in mind the stoke goes up more due to the springs. The stroke of a Sidewinder cannot be compared to other rotaries as the hit is completely different)
Polarity: Positive up - spins motor clockwise - slaps harder, ideal for large grouping liners
Positive down - spins motor counterclockwise -slightly passive hit, ideal for shading and fine line
Aaron Cain Roundback Shader Ver 2.0, based on the OG Sand Cast Iron Roundbacks Aaron did years ago, now CNC cut with a few improvements!
- New CNC Cut Iron Frame - HD Black Powder Coat Finish - Deluxe Workhorse Blackened Steel Hardware - 1" 8 Wrap Custom Dyed Money Coils - Long Stroke with a Medium Hit - Running 100-105 Hz @ 6.5 V unloaded - Pushing 5's to 11's no problem - Weighs 6.45 Ounces - MADE IN THE USA
Workhorse Irons
Aaron Cain Roundback Liner - Black x Black
Regular price$425.00 USD
Aaron Cain Roundback Liner Ver 2.0, based on the OG Sand Cast Iron Roundbacks Aaron did years ago, now CNC cut with a few improvements!
- CNC Cut Iron Frame - HD Black Powder Coat Finish - Deluxe Workhorse Blackened Steel Hardware - 1" 8 Wrap Custom Dyed Money Coils - Medium speed with a Medium Stroke and a Solid Hit - Running 130-135 Hz @ 6.5 V unloaded - Pushing 3's to 7's with ease, turn up volts to push 9-11s - Weighs 6.45 Ounces - MADE IN THE USA