Featherweight Aluminum Dan Kubin V3/24 Sidewinder with EXTRA HIT and MORE POWER!

This new version is built with a solid brass weighted armature bar for even more hit and power than the standard V3/24 Sidewinder! These are for those looking to push extra large groupings or to just have a machine with lots of power and hit.

These Power Sidewinders are not for everyone, the standard version is more than enough hit for most. Especially with the new V3/24 Needle Bar Guide added, eliminating the need for a rubber band, reducing drag and improving performance. 

Highlights:

• FEATHERWEIGHT Black Polished Aluminum Frame with Blackened Hardware
  
• Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.5 ounces total!
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.

RCA Specifications:

• RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
• This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
• This will also work good with a right-angle RCA cord.
• Clip Cord option still works, it is just wired backwards.
• The position of the battery makes the machine’s balance point much more forward, like a pen.

Description:

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  Intended for experienced artists who don’t want to mess around.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

Chris Smith Supreme Liner! 

Built with an aluminum upright and ass end with a steel base/vise, this half and half machine is lightweight, well-balanced, and built for all day everyday tattoos.

Highlights:

• CNC Cut Aluminum Frame
• Steel Base and Vise Inlaid into the Aluminum Frame
• Deluxe Blackened Steel Hardware, Spring Saddle, and Clip Cord Yoke Screw
  
• 6 Wrap 1.25” Tape Coils with Oversized Cap
  

Specifications:

• Pushes 5’s to 14’s Easy
• Long Stroke, Medium Speed with a Heavy Hit
  
• 130-135 Hz at 6.5 V unloaded
• Weighs a mere 5.6 oz
  

Made in the USA

Hustle Butter Antibacterial Foaming Soap

AVAILABLE IN TWO SIZES: 7 fl oz and 3.4 fl oz (TSA-friendly!)

Hustle Butter Antibacterial Foaming Soap is the perfect multitasking tattoo wash - perfect for use in-process by artists and as aftercare by clients. This vegan antibacterial foaming soap is tough on germs but gentle on skin, making it the ideal tattoo soap and skin cleanser. Formulated to replace “green-soap”, it is used and loved by artists and clients worldwide. Made with a gentle formula, this tattoo cleanser soothes skin without drying it out, and is made specifically for tattooed skin.

Now available in two sizes - 7 fl oz & 3.4 fl oz - whatever your needs are, we have a foamer for you. Our standard 7 fl oz size is perfect for in-process and larger pieces, as well as for keeping healed tattoos clean and fresh. Our 3.4 fl oz size is designed for on-the-go use - it’s the perfect travel companion and is TSA-compliant and travel friendly. Whether you are traveling for a new tattoo or washing a fresh piece on-the-go, this size is perfect for your purse, suitcase or bag.

Key Features & Benefits:

• Made with cruelty-free, vegan-friendly ingredients
• Antimicrobial soap cleanses skin and keeps it moisturized
• Keeps sanitized tattooing area clean
• Great for post-tattoo and piercing care
• Green Soap Replacement

What’s In It?

Active Ingredient: Benzalkonium Chloride 0.10% (Antibacterial)
Inactive Ingredients: Aloe Barbadensis Leaf Juice, Coceth-7, PPG-1-PEG-9 Lauryl Glycol Ether, PEG-40 Hydrogenated Castor Oil, Soytrimonium Chloride, Fragrance (Parfum), Propylene Glycol, Glycerin, Water (Aqua), Chamomilla Recutita (Matricaria) Flower Extract, Camellia Sinensis Leaf Extract, Arnica Montana Flower Extract, Hamamelis Virginiana (Witch Hazel) Leaf Extract, Symphytum Officinale Leaf Extract, Rosmarinus Officinalis (Rosemary) Oil, Methylchloroisothiazolinone, Methylisothiazolinone, Benzyl Benzoate, Citronellol, Coumarin, Geraniol, Hexyl Cinnamal, Hydroxycitronellal

How To Use:

1. Wet skin, apply palmful of product to hands, and rub onto skin.
2. Wipe or rinse off and pat dry with a paper towel (bath towels/washcloths are not recommended as they can leave fibers behind).

Dan Kubin V3/24 Sidewinder!

Highlights:

• Bronze Black Plated Brass Frame with Black Hardware(*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.

Description:

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan.  All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

Blackwork Nitrile Gloves

Made from a non-latex nitrile formula, these new Blackwork medical grade exam gloves offer all of the benefits of natural rubber latex with none of the allergen problems associated with latex. Blackwork gloves were specially formulated / designed to reduce hand fatigue during long tattoo sessions. Using their patented formula, they've created a glove with almost zero resistance while maintaining comfort, elasticity, and strength. Textured finish for wet and dry gripping ability.

• 100ct. per box, 10 box/case
• Patented Ultra Elastic Black Nitrile Formula
• Near Zero Resistance, reduced hand fatigue over long hours
• Textured surface for greater grip and tactile sensitivity
• Smaller box size reduces shipping cost
• Extreme elasticity

Their new patented Black Nitrile formula is the most scientifically advanced glove in the Tattoo Industry. Unrivaled protection, Zero resistance, Incredible comfort, and a textured surface with unbelievable tactile sensitivity. 

Workhorse Irons x Adam Hathorn T-Shirt

Back by popular demand.

Originally released years ago, this classic Adam Hathorn (Honky Konger) design returns with an updated monochromatic color palette, oversized back print, and left chest WHI monogram.

Known for his work as a tattooer, illustrator, and the unmistakable visual style behind Benchwarmers, Adam created this custom Workhorse boxing horse as a tribute to the hardworking spirit that has always been at the core of the brand.

Equal parts tattoo culture, cartooning, and classic Honky Konger humor, it's a design that has remained a favorite for years and one we're excited to bring back.

Printed on Comfort Colors 1717 heavyweight t-shirts.

Made from garment-dyed ring-spun cotton with a relaxed fit and broken-in feel from day one. Comfortable enough for long days in the shop, the road, or wherever tattooing takes you.

Details

• Original artwork by Adam Hathorn (Honky Konger)
• Oversized back print
• Left chest WHI monogram
• Printed on Comfort Colors 1717 heavyweight t-shirts
• Garment-dyed ring-spun cotton
• Relaxed fit
• Soft-washed for a broken-in feel

A Workhorse favorite returns.

Workhorse Model 6 Liner

Formerly built by Marv Lerning, this is an updated and modernized version of Marv's 6 Liner inspired by the Waters Model 6 Frame. Now with updated geometry for more power and efficiency, plus swing gate vise added to guarantee ease of use with any and all tubes. 

We are stoked to release this new Workhorse Model built in house by our highly trained and knowledgeable machine techs. Bringing us back to our roots with an affordable base model machine made with shared parts and technology to reduce costs. We offer lots of limited and custom high-end machines these days and wanted to release a new base model option at base model pricing.

Highlights:

• Full Size Frame milled in house from a solid block of Ductile Iron
• HD Flat Black Powder Coat Finish
• Deluxe Workhorse Hardware with Black Oxide Finish
• Swing Gate Steel Vise
• Custom 8 Wrap 1" Coils with 1/4" Steel Yoke 
• High End Specialty Steel Springs
• Solid Copper Contact with Allen Key Insert
• Reverse Rear Binder Setup with frame ground on coil deck

Specifications:

• Long Stroke with a solid hit great for 5s to 14s
  
• Medium Speed, running around 135-140 unloaded @ 6.5 Volts
• 6.5 Ounce Weight

Made in the USA

SOBA Boomerang Liner!!

CNC Milled version of SOBA's braze-up and bolt-up Boomerang, streamlined into a one piece frame with very versatile swing gate vise.

These are finely tuned. With no load most of them run in the 140hz range. At 6 volts you will get smooth medium to fine lines- think 05 and 08 microns. At 7.5 they will bury a straight 9- think brand new sharpie.

Highlights:

• CNC Cut Ductile Iron Frame 
  
• Drilled Out and Lightened Upright 
  
• Swing Gate Vise with and Internal Spring for ease of use
  
• Custom Diamond Pearl Powder Coat Finish
  
• Custom Deluxe Antiqued Brass Hardware
  
• Deluxe 1" 8 Wrap Black Gaffers T-Top Coils

Specifications:

• Medium Quick Speed with a Solid Hit 
  
• Great for Smaller to Medium Sized Groupings
  
• Pushing 3's to 9's easy, turn up a little for 11's
  
• Running 140-145 Hz @ 6.5 V Unloaded
  
• Weighs 6.8 oz
  

Made in the USA

Juan Puente OG Shader - Black x Black

Highlights:

• CNC Cut Iron Frame
• HD Custom Black Finish
  
• Deluxe Black Hardware
• Swing Gate Vise Guaranteed to lock tight on any tube
• 1.25" 8 Wrap Standard Electrical Tape Coils
  

Specifications:

• Slow Speed with a Solid Hit
• 110-115 Hz at 6 V Unloaded
  
• Pushing up to 13's All Day
• Weighs 7.2 oz

Made in the USA