Home / Dan Kubin / DK 1" Swift Tip Cover

Workhorse Irons

DK 1" Swift Tip Cover

Regular price $4.00 USD

Grouping	Price	Inventory	Quanity
100	$4.00 USD	Available
1000	$30.00 USD	Available

New DK Swift Tip System!

This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your work station.

Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health.

Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips!

This is a bag that serves as a barrier on your Swifftip grip.

Simply slide over the grip, and snap the tip in over the bag.

This allows for a proper barrier from cross contamination.

It is recommended to still wipe the grip off with a sterilant as you would your work station or armrest.

This bag is meant for the 1" grip.

*BUY IN BULK AND SAVE 20%

Better tools to make better tattoos.

Share Share on Facebook Tweet Tweet on Twitter Pin it Pin on Pinterest

Dan Kubin Mojobox V2 - Polished Nickel x Gold

Regular price $950.00 USD

Dan Kubin Mojobox V2.2

Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!

Now with more versatility and ease of hit adjustment throughout the tattoo. It is more ergonomic, more reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary.

The focus of its design is to be more like a shader/packer that can also line well, whereas the Sidewinder is more of a liner that can shade. If you prefer more punch at a slower to medium speed, this is a great option. Excellent for fine line, black and grey, color packing with any size mag. Can drive 14 liners, if you prefer to “set the needle into the skin” whereas the Sidewinder prefers to have the needle floated across the skin.

The Remastered Mojobox has a numbered upstroke wheel (same as the V3r) which allows for a wide range of versatility throughout the hit once in the 5.3 and up voltage ranges. Simply turn the stroke wheel for a longer or shorter stroke. The 5 setting is middle of the road and what most people use. Turn up towards 9 for longer srtroke and down towards 1 for shorter stroke.

Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive which is the nature of a cartridge.

Typical operating range: 4 - 6 volts, sweet spot for most is 5 Volts on the 5 setting.

Brass Frame with High Polish Nickel Plated Finish and 24k Gold Plated Parts

Weight: 5 oz

Customer Reviews

Based on 2 reviews Write a review

Dan Kubin Sidewinder v7.5 - Polished Nickel w/ Ebony

Workhorse Irons

Dan Kubin Sidewinder v7.5 - Polished Nickel w/ Ebony

Regular price $1,100.00 USD

*7.5 highlights: Made a straight angle on drive spring shelf on the armature bar, allowing for a more effortless and graceful hit.

*Impact screw and Impact pin are now adjusted with the 1.5mm allen key provided with the machine.

*More prominent timing marks on the sideplate for the impact pin. (for advanced tuning/stroke adjustment, this helps with being more intuitive)

*Cleaner sound/better acoustics.

* Side locking screw is positioned to secure the impact screw most effectively

The Sidewinder 7 is the most revolutionary Sidewinder yet. Now, not only is it the supreme liner, it now is great in the lower volt range for shading to color packing, fine line and stippled whip shading techniques.

It has 5 stroke positions ranging from 3.5-4mm. While tattooing, hit is controlled with adjustable return spring tension.

The impact screw is adjustable. This allows for more precise tuning. It still has an adjustment pin on the frame , which will slightly change the stroke, or allow for a quick impact adjustment.

The main goal for this batch is for simple tuning for the end user, but with the option/ability to dial it in precisely for those who know how they want their machine to run.

If you want a softer hitting machine, you don’t have to compromise the stroke length. You can simply adjust the return spring tension on the fly throughout the tattoo.

Recommended voltage range: 4 - 6.5

Weight: 6.2 Ounce

*keep in mind that the weight is very forward, low and balanced. This said, even with a weight of 6.2 oz, there is very little strain on the wrist.

st.

Customer Reviews

Based on 2 reviews Write a review

Workhorse Irons

Dan Kubin MCi - Gold x Gold

Regular price $895.00 USD

NEW Dan Kubin MCi (Mini Cranker with Impact)!

Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.

Specs:

Steel Frame with 24k Gold Plated Frame and Hardware
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise

Setup / Usage:

Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.

Use and Care:

Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.

Enjoy!

Customer Reviews

Based on 2 reviews Write a review

Workhorse Irons

Dan Kubin MCi - Antique Nickel

Regular price $825.00 USD

NEW Dan Kubin MCi (Mini Cranker with Impact)!

Specs:

Steel Frame with durable Antique Nickel Plated Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise

Setup / Usage:

Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.

Use and Care:

Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.

Enjoy!

Customer Reviews

Based on 2 reviews Write a review

Workhorse Irons

Dan Kubin MCi - Rubbed Bronze

Regular price $825.00 USD

NEW Dan Kubin MCi (Mini Cranker with Impact)!

Specs:

Steel Frame with durable Rubbed Bronze Plated Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise

Setup / Usage:

Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.

Use and Care:

Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.

Enjoy!