• High-grade Aluminum body precision milled
• Custom Black Anodized Parts with HD Orange Powder Coated Frame, plus Blackened Deluxe Binders and Cast Wingnut
• Custom Etched Cory Rogers Skull and Daggers plus Builder Intials
  
• Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
• Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
• Forward facing wingnut that won't ride your hand or get in your way
• 4 mm stroke that works great for color packing, shading and also large groupings lining
• Pushes 5 to 49 mag and 9 to 18 Rounds no problem
• Runs best anywhere between 5 and 10 volts
• Most are lining between 8-10 Volts for larger groupings, 5-9 volts for color packing and B&G work
• Great with Needle on Bar or Cartridges
• Lightweight weighing in at a mere 4.5 oz

*Spring Sale $75 off Limited Time Only*

Legacy Edition Dan Kubin V3R Sidewinder

*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.

"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.

Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.

These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly." 

Thanks for looking - Dan.

Machine Specs:

• Antique Nickel Plated Brass Frame (*Finish may vary)
  
• Black DK Thumbscrew and Blackened Brass OG Armature Bar
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
  

• Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
  

Machine Setup:

• Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
  
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

*Completely black oxided.  *please note that the brass will peak though over time where it sees heavy wear, adding to its character.

For more info please watch the V3R Setup and Tuning Video:

*Spring Sale $75 off Limited Time Only*

Legacy Edition Dan Kubin V3R Sidewinder

*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.

"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.

Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.

These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly." 

Thanks for looking - Dan.

Machine Specs:

• 24k Gold Plated Brass Frame (*Finish may vary)
  
• Black DK Thumbscrew and Blackened Brass OG Armature Bar
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
  

• Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
  

Machine Setup:

• Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
  
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

*Completely black oxided.  *please note that the brass will peak though over time where it sees heavy wear, adding to its character.

For more info please watch the V3R Setup and Tuning Video:

• Wider springs for more durability.
• Large, easy to turn, hardened steel stroke wheel. Pre-set stroke range and middle timing mark to prevent the machine from getting too far out of tune when experimenting.
• Hardened alloy steel impact pin. Positioned towards the rear of the frame to help with noise
• Large cam with precise timing mark. Allows for easier, and more precise impact alignment checks
• Smooth, easy clamping tube vice.
• Forward weight distribution for better ergonomics.
• Beautiful brass armature bar, perfectly balanced for a strong, confident, and  consistent hit.  
• O-ring groove in the bar allows for a more silent option (though will reduce performance as well)
• Reliable Mabuchi motor. -because they run forever without losing consistency. 

• Standard (brass frame construction): 6oz
• Featherweight  (7075 aluminum frame): 4.4 oz

• High-grade Aluminum body precision milled
• Custom Gold and Black Anodized Parts with HD Seafoam Powder Coated Frame, plus Blackened Deluxe Binders and Cast Wingnut
• Custom Etched Cory Rogers Skulls and Daggers
• Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
• Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
• Forward facing wingnut that won't ride your hand or get in your way
• 4 mm stroke that works great for color packing, shading and also large groupings lining
• Pushes 5 to 49 mag and 9 to 18 Rounds no problem
• Runs best anywhere between 5 and 10 volts
• Most are lining between 8-10 Volts for larger groupings, 5-9 volts for color packing and B&G work
• Great with Needle on Bar or Cartridges
• Lightweight weighing in at a mere 4.5 oz

Limited Edition Adam Ciferri Pitbull Liner - Seafoam x Black

Specifications:
- Tuned for all-day, every-day street shop and/or custom tattooing
- Heavy hit that easily pushes 5's to 11's
- Runs 125-130z @ 6.5 Volts Unloaded
- CNC Cut Iron with the highest precision and care
- HD Ugly Green Powder Coat Finish
- Blackened Deluxe Hardware
- 1.125" 8 Wrap Custom Black Reflective Coils
- Weighing in at 6.4 ounces
- MADE IN THE USA

A few words from Adam on his history with this machine:
"I think most of you know that I've been making a version of this machine since about 1999, but, I don't know how many of you really know the story of how this machine came to be…

In mid 1999, the first Pitbull outliners were made by chopping down some bulldog shaders. They ran a bit slow and punchy for what I'd call an outliner, but, they definitely did the job. Over the years, there have been a few iterations of this machine, and almost all of them were based on, basically, cutting up a shader and, either making due with the geometry, or adjusting the geometry.

What we have here is the new version I designed for Workhorse Irons. This machine is based on the dedicated geometry that I've wanted for this machine since, just about, day one. It lends itself to a few different liner configurations without needing to apply any hocus-pocus. Small groupings? Sure. Medium groupings? Yes. Big, fat, ig'nunt-ass outlines? Fuck yeah-continually, since 1999! This machine has a great range, but is basically set up to make big fucking outlines, quickly."
Respectfully, Adam C

New SOBA V2 Mini Clipper Liner! Limited Edition Green!

New forward weighted version of the Mini Clipper designed and built by SOBA. These machines go above and beyond, providing both superior balance and performance. Made with a thick aerospace aluminum frame to reduce weight while also minimizing vibration and twang, plus an oversized milled navy brass vise and thumbscrew to keep the majority of weight over the artist's hand reducing clip cord pull and hand fatigue.

- CNC Cut Aerospace Aluminum Frame with thick inlaid yoke for proper conductivity
- Raw Polished Finish
- 24k Gold Plated Weighted Brass Vise and Thumbscrew
- 24k Gold Plated Deluxe Brass Hardware plus Custom Drop Down Rear Binder
- 1" 8 Wrap Custom Coils
- Great for Medium to Large Groupings
- Medium Speed with a Hard Hit
- Pushing 5's to 14's All Day
- Running 130-135 Hz @ 6.5 V Unloaded
- Weighing in at a total 6.5 ounces with almost half the weight being the vise and thumbscrew
- MADE IN THE USA