*Spring Sale $75 off Limited Time Only*

Legacy Edition Dan Kubin V3R Sidewinder

*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.

"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.

Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.

These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly." 

Thanks for looking - Dan.

Machine Specs:

• Black Oxide Brass Frame (*Finish may vary)
  
• Black DK Thumbscrew and Polished Brass OG Armature Bar
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
  

• Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
  

Machine Setup:

• Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
  
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

*Completely black oxided.  *please note that the brass will peak though over time where it sees heavy wear, adding to its character.

For more info please watch the V3R Setup and Tuning Video:

New B&G Race Horse Shaders machined from Lightweight Aerospace Aluminum with Swing Gate Vises guaranteed to lock tight on any tube! These machines are setup and designed to run quicker and lighter, great for building up layers, doing color blends and portrait work.

- Anodized Featherweight Aluminum Frame
- Steel Swing Gate Vise guaranteed to lock tight on all tubes
- Deluxe Black Hardware
- 8 Wrap 1" Custom Coils
- Super Smooth for B&G, Soft and Quick for Building Layers
- 115-120 Hz at 6.5 V unloaded
- 5.4 oz
- MADE IN THE USA

NEW Mini Version of Mike Pike's Mean Mugger Shader! Limited Edition Hot Pink x Black

• Hot Pimnk Powder Coated Iron Frame
• Deluxe Blackened Hardware
• 1" Black Shrink Coils
  
• Swing Gate Vise Guaranteed to Lock Tight on Any Tube
• Running 110-120 Hz @ 6.5 V unloaded
• Medium Speed with a Solid Hit
• Pushing 5's to 13's all day
• Weighs 7 oz
• MADE IN THE USA

NEW Mini Version of Mike Pike's Mean Mugger Liner! Limited Edition Hot Pink x Black

• Hot Pink Powder Coated Iron Frame
• Deluxe Blackened Hardware
• 1" Black Shrink Coils
  
• Swing Gate Vise Guaranteed to Lock Tight on Any Tube
• Running 135-140 Hz @ 6.5 V unloaded
• Medium Speed with a Solid Hit
• Pushing 3's to 11's all day
• Weighs 7 oz
• MADE IN THE USA

New SOBA V2 Mini Clipper Liner! Limited Edition Green!

New forward weighted version of the Mini Clipper designed and built by SOBA. These machines go above and beyond, providing both superior balance and performance. Made with a thick aerospace aluminum frame to reduce weight while also minimizing vibration and twang, plus an oversized milled navy brass vise and thumbscrew to keep the majority of weight over the artist's hand reducing clip cord pull and hand fatigue.

- CNC Cut Aerospace Aluminum Frame with thick inlaid yoke for proper conductivity
- Anodized Satin Green Finish
- Raw Brass Vise and Thumbscrew
- Deluxe Brass Hardware plus Custom Blackened Steel Drop Down Rear Binder
- 1" 8 Wrap Custom Coils
- Great for Medium to Large Groupings
- Medium Speed with a Hard Hit
- Pushing 5's to 14's All Day
- Running 130-135 Hz @ 6.5 V Unloaded
- Weighing in at a total 6.5 ounces with almost half the weight being the vise and thumbscrew
- MADE IN THE USA

• Tuned for all-day, every-day street shop and/or custom tattooing
• Medium/Quick Speed with a Solid hit that easily pushes 5's to 13's...also able to push very large groupings if you bump the volts up a bit
• Runs 110-115 Hz @ 6.5 Volts Unloaded
• Good for Quick Color Packing or B&G Work / Color Blends
• CNC Cut Iron with the highest precision and care
• Custom Black Reflective 1" Keg Coil
• HD Poly Stain Gold Powder Coat Finish
• Deluxe Blackened Hardware
• Weighs 6 oz
• MADE IN THE USA

A few words from Adam about this machine:
"The Ghost Dog Shader is tuned for all-day, every-day street shop and/or custom tattooing. Weighing in at a mere 6 ounces, this is a machine that punches way above it's weight class. Perfect for tattooers who like the weight of a rotary machine but prefer the feel and performance of a coil machine"
-Respectfully, Adam C

• Tuned for all-day, every-day street shop and/or custom tattooing
• Medium speed with enough hit to push 3's to 14's no problem
• Runs 120-125 Hz @ 6.5 Volts Unloaded, crank up to 9-10 Volts for large groupings
• CNC Cut Iron with the highest precision and care
• Custom Black Reflective 1" Keg Coil
• HD Poly Stain Gold Powder Coat Finish
• Deluxe Blackened Hardware
• Weighs 6 oz
• MADE IN THE USA

A few words from Adam about this machine:
"The Ghost Dog Liner is set up to make solid single pass outlines with ease. Weighing in at a mere 6 ounces, this is a machine that punches way above it's weight class. Perfect for tattooers who like the weight of a rotary machine but prefer the feel and performance of a coil machine"
-Respectfully, Adam C.

• High-grade Aluminum body precision milled
• Custom Green Anodized Parts with Rainbow Glitter Powder Coated Frame, plus 24k Gold Plated Binders and Wingnut
• Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
• Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
• Forward facing wingnut that won't ride your hand or get in your way
• 4 mm stroke that works great for color packing, shading and also large groupings lining
• Pushes 5 to 49 mag and 9 to 18 Rounds no problem
• Runs best anywhere between 5 and 10 volts
• Most are lining between 8-10 Volts for larger groupings, 5-9 volts for color packing and B&G work
• Great with Needle on Bar or Cartridges
• Lightweight weighing in at a mere 4.5 oz

Limited Mike Pike x Destroy Troy Teacup Liner - Pink x Black

Special limited edition collaborative machines by Mike Pike and Destroy Troy! This has been in the works for quite a while, but after many frame adjustments, tweaks and updates, they are dialed in and ready. Very smooth running, extremely well balanced, and sturdy, these forward weighted machines are finely tuned and built for years of trouble free use.

Highlights:

• Thick Aluminum Teacup Frame with various updates to help with overall long-term strength and vibration reduction
• Chunky Jonesy Style Steel Vise designed to keep more weight over your hand to help balance the pull of your clipcord and reduce hand fatigue
• Blackened Destroy Troy Warp Drive Cray Bar
  
• Custom 1.125" 7 Wrap Coils
  
• Pink Disco Gold Powder Coated Aluminum Frame
• Blackened Steel Destroy Troy Forward-Weighted Guillotine Vise
  
• Deluxe Blackened Hardware
  
• Blackened Spring Shelf Yoke for Superior Connectivity
• Deluxe Copper Contact Screw
  
• Stainless Springs

Specifications:

• Medium Speed with a Solid Hit
• Running  around 135 Hz Unloaded at 6.5V
• Great for use with 3s to 9s, turn up for 11s
• 7.5 oz Forward Weighted Machine
• Made in the USA

New Mike Pike PMA Direct Drive Rotary!

After a couple years of minor tweaks and lots of testing, the new Mike Pike Direct Drive Rotary is finally ready! Not necessarily a reinvention of the wheel, but applying his years of knowledge tattooing and building rotary machines, Pike dialed in these Direct Drives and simply made a great running Rotary.

Built using only the finest components to produce a great all around direct drive that is smooth running, consistent, and rock solid for years of trouble free use. Made with powerful high end motors, an adjustable Cam to accommodate any stroke, vertical swing gate vise guarantee to grip tubes with no issue, and top of the line aluminum that is both lightweight and strong enough to stand the test of time.

- Limited Edition Run of White Disco Gold Powdered Coated Aluminum Frames PLUS 24k Gold Plated Motor Cap, Swing Gate Vise, and Hardware.
-High-grade Aluminum body precision milled frames and components
- Powered by a top of the line Maxon motor described by Mike Pike to be the "best motor he has ever used in a rotary"
- Comfortable and well balanced with a vertical swing gate tube vice that will bite and hold all disposable and stainless tubes
- Adjustable Brass Cam with PMA reference marks to help keep track of stroke settings and adjustments. Simply loosen the cam set screw, pull out the inner cam and insert it back in at either a shorter or longer setting to change the stroke quick and easy
- Pushes up to 25 mag and up to 18 Rounds no problem, Needle on Bar or Cartridges
- Runs best anywhere between 5 and 10 volts depending on what you are pushing and how you are tattooing
- Lightweight weighing in at a mere 4.5 oz
- Clipcord Connection

Made with love in the USA by Mike Pike and his 40+ years of experience tattooing and building machines.

Thanks and enjoy,
Mike Pike

Model 6 Shader Frame

• CNC Cut Iron Shader Frame
  
• Designed by Marv Lerning, inspired by the classic Waters Model 6
• Black Zinc Finish
• Geometry for 1.25" Coils
• Standard Pinch Vise
• Weighs 3.10 oz

Made in the USA

Model 6 Liner Frame

• CNC Cut Iron Liner Frame
  
• Designed by Marv Lerning, inspired by the classic Waters Model 6
• Black Zinc Finish
• Geometry for 1.25" Coils
• Standard Pinch Vise
• Weighs 2.9 oz

Made in the USA

Limited Edition Adam Ciferri Pitbull Liner - Seafoam x Black

Specifications:
- Tuned for all-day, every-day street shop and/or custom tattooing
- Heavy hit that easily pushes 5's to 11's
- Runs 125-130z @ 6.5 Volts Unloaded
- CNC Cut Iron with the highest precision and care
- HD Seafoam Powder Coat Finish
- Blackened Deluxe Hardware
- 1.125" 8 Wrap Custom Black Reflective Coils
- Weighing in at 6.4 ounces
- MADE IN THE USA

A few words from Adam on his history with this machine:
"I think most of you know that I've been making a version of this machine since about 1999, but, I don't know how many of you really know the story of how this machine came to be…

In mid 1999, the first Pitbull outliners were made by chopping down some bulldog shaders. They ran a bit slow and punchy for what I'd call an outliner, but, they definitely did the job. Over the years, there have been a few iterations of this machine, and almost all of them were based on, basically, cutting up a shader and, either making due with the geometry, or adjusting the geometry.

What we have here is the new version I designed for Workhorse Irons. This machine is based on the dedicated geometry that I've wanted for this machine since, just about, day one. It lends itself to a few different liner configurations without needing to apply any hocus-pocus. Small groupings? Sure. Medium groupings? Yes. Big, fat, ig'nunt-ass outlines? Fuck yeah-continually, since 1999! This machine has a great range, but is basically set up to make big fucking outlines, quickly."
Respectfully, Adam C

New B&G Race Horse Shaders machined from Lightweight Aerospace Aluminum with Swing Gate Vises guaranteed to lock tight on any tube! These machines are setup and designed to run quicker and lighter, great for building up layers, doing color blends and portrait work.

- Anodized Featherweight Aluminum Frame
- Steel Swing Gate Vise guaranteed to lock tight on all tubes
- Deluxe Black Hardware
- 8 Wrap 1" Custom Coils
- Super Smooth for B&G, Soft and Quick for Building Layers
- 115-120 Hz at 6.5 V unloaded
- 5.4 oz
- MADE IN THE USA