Deluxe Binding Post Set

High grade steel, precision milled to trade standard measurements of 0.625" length and 0.375" diameter. Rear Binder is designed for Horizontal use.

Each set includes the front and rear binder, steel washers, fiber washers, screws, nylon bead, and Flat Head Silicone Bronze Contact Screw.

Kit Includes: SOBA’s Pilot frame, Shaders come with 1 pair of 8 wrap 1.25" coils and Liners come with 1 pair of 6 wrap 1.125" coils , appropriate armature bar, front and rear steel binding posts, contact screw, all washers including insulators, black, and magnetic steel shims, all screws, capacitor, cast iron wing nut, Allen wrench, and 2 sets of fully punched springs. Essentially everything needed to assemble a complete machine. Skills and instructions NOT included. MADE IN THE USA.

Dan Kubin Weighted Impact Screw Kit

"New updated weighted impact screw! I found that it helps with the stability of the hit, and improved overall performance. Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band."

Thanks - Dan

Weighted Impact Kit Specifications:

• Upgrade for Dan Kubin V3R with updated armature bar (Late 2019 to Current)
  
• Custom heat treated tool steel RHC 60 plus o-ring
• Easy swap out to increase the hit while improving the overall feel and sound
• Kit also includes both the 1.5mm and 2mm L wrench

Upgrade Step by Step: (see pictures for guidance)

1. Use the 1.5mm wrench to loosen the set screw on the side of the armature bar. Half a turn should loosen it enough to easily remove the impact screw.
2. Hold down the armature bar and use the 2mm wrench to remove the old impact screw.
3. Once removed, use the 1.5mm wrench to insert and tighten the weighted impact screw down until the o-ring starts to bulge out as it makes contact with the top of the armature.
4. Tuning - this is the most important step and will effect the timing and stroke of your machine.
1. While holding the armature bar down, roll the cam back until it makes contact with the vertical spring and gently stops. In this position the timing mark on the cam should align with the center of the timing mark on the frame.
2. If the timing mark on the cam is on the low side of the timing mark on the frame, tighten the weighted impact a little until it raises up to the center of the timing mark on the frame.
3. If the timing mark on the cam is on the high side, the impact is too far in and needs to be backed out (loosened) until the timing mark on the cam is in the center of the timing mark on the frame.
5. Use the 1.5mm wrench to tighten the set screw on the side of the armature bar.
6. Your machine is now upgraded and ready to use. One note would be that the new impact works well with the rubber band pulled slightly higher on the needle bar so it is perpendicular when the armature is in the down position.

Front & rear set; includes washers, screws, and a silicon bronze contact screw.

New V4 Adam Ciferri Ghost Dog Shader Hybrid

Updated version includes a new slide vise to better grip all the various tube options, dialed in geometry for better performance, plus a new rear binder setup to allow more clip cord spacing.

• Tuned for all-day, every-day street shop and/or custom tattooing
• Medium/Quick Speed with a Solid hit that easily pushes 5's to 13's...also able to push very large groupings if you bump the volts up a bit
  
• Runs 110-115 Hz @ 6.5 Volts Unloaded
• Good for Color Packing or Color Blends
• CNC Cut Iron with the highest precision and care
• 1" Custom Keg Coil
• Standard Workhorse Red Oxide Finish
• Standard Workhorse Blackened Hardware
• Weighs 6 oz
• MADE IN THE USA

A few words from Adam about this machine:
"The Ghost Dog Shader is tuned for all-day, every-day street shop and/or custom tattooing. Weighing in at a mere 6 ounces, this is a machine that punches way above it's weight class. Perfect for tattooers who like the weight of a rotary machine but prefer the feel and performance of a coil machine"
-Respectfully, Adam C.

Joshua Bowers lightweight RCA Cord

Designed with function and maintenance in mind, this lightweight RCA Cord is made with the finest components ensuring a reliable and consistent connection.

• Light weight non-stick cord material
• High-grade Switchcraft Gold Right Angle Plug
• High-end matching Amphenol Plug
• 6 foot length
• Very lightweight at a mere 2.3 ounces
• Limited 1 Year Warranty covers product defects, not everyday wear and tear.

• MADE IN THE USA

Nylon beads (for set screw, prevents contact damage) pack of 10

New DK Swift Tip System!  

This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your work station. 

Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health. 

Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips! 

DK Swift Tips - 1 to 5 Round - Box of 24 Tips (Grip Not Included)

*Must be used with DK Swift Tip Grip

These tips have great visibility and come to a nice point.  The biggest benefit is being able to see more needle even when you don't have a lot of needle hanging out.

The shape of the round tips is in between a round and a diamond. That said, it is the best of both worlds.  It allows for maximum verastility and stability for a wider range of sizes.

This tip configuration is for your smaller round needle groupings.

I prefer it for my singles to 5's, and even tight or bugpin 7's.

These tips are hydrophobic and have an antimicrobial additive in them. That said, you may need to check with your local health dept for protocol on single use plastic products used in the tattooing process.. (such as ink caps)

*blister packaged tips coming soon

Made in house at DK Rotary in Kansas City MO, USA

Better tools to make better tattoos.

Workhorse Needle Bar Grommets (100)