New V4 Adam Ciferri Ghost Dog Shader!

Updated version includes a new slide vise to better grip all the various tube options, dialed in geometry for better performance, plus a new rear binder setup to allow more clip cord spacing.

A few words from Adam about this machine:
"The Ghost Dog Liner is set up to make solid single pass outlines with ease. Weighing in at a mere 6 ounces, this is a machine that punches way above it's weight class. Perfect for tattooers who like the weight of a rotary machine but prefer the feel and performance of a coil machine"
-Respectfully, Adam C.

Highlights:

• CNC Cut Iron with the highest precision and care
• Custom Olive Green 1" Keg Coil
• Custom Plateau Green Powder Coat Finish
• Deluxe Workhorse Blackened Hardware

Specifications:

• Tuned for all-day, every-day street shop and/or custom tattooing
• Medium/Quick Speed with a Solid hit that easily pushes 5's to 13's...also able to push very large groupings if you bump the volts up a bit
  
• Runs 110-115 Hz @ 6.5 Volts Unloaded
• Weighs 6 oz

Made in the USA

Dan Kubin MCi (Mini Cranker with Impact)!

Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.

Highlights:

• Steel Frame with 24k Gold Plated Frame and Hardware
  
• Weighted Brass Armature
• Deluxe Kubin Components including DK Thumbs and updated Slide Vise
• Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
• Higher voltage between 5 - 7 Volts for most Lining
• Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work

Setup / Specifications:

• Works well with Standard Needle on Bar AND with Cartridges
• Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
• This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
• Polarity is not crucial, but will run slightly more efficiently with Positive Down
• The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
• Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.  
• Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact. 

Use and Care:

• Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
  
• After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings.  DO NOT FILL THE MOTOR WITH OIL!!
• Keep sterilants away from all moving and electrical components! Sterilants are corrosive and will damage your machine if used carelessly.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All MCI machines go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current MCIs are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

Dan Kubin MCi (Mini Cranker with Impact)!

Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.

Highlights:

• Steel Frame with durable Antique Nickel Plated Finish
  
• 24k Gold Plated Hardware
• Weighted Brass Armature
• Deluxe Kubin Components including DK Thumbs and updated Slide Vise
• Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
• Higher voltage between 5 - 7 Volts for most Lining
• Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work

Setup / Specifications:

• Works well with Standard Needle on Bar AND with Cartridges
• Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
• This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
• Polarity is not crucial, but will run slightly more efficiently with Positive Down
• The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
• Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.  
• Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact. 

Use and Care:

• Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
  
• After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings.  DO NOT FILL THE MOTOR WITH OIL!!
• Keep sterilants away from all moving and electrical components! Sterilants are corrosive and will damage your machine if used carelessly.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All MCI go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current MCI are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

¡SOBA ESTÁ DE VUELTA! Después de su Sobbatical 2020, BJ está de vuelta construyendo una cantidad limitada de máquinas de bobina personalizadas, trabajando en una nueva producción y ahora fabricando máquinas rotativas.

Sombreadores y revestimientos piloto de hierro fundido SOBA:

Después de más de 20 años de producción, numerosas actualizaciones de mecanizado y ajustes de ajuste, estos son los modelos de más larga duración que vendemos. Con una geometría tolerante a largo plazo, estas máquinas son los caballos de batalla probados, verdaderos y consistentes del tatuaje. Construido para durar toda la vida con poco desorden o alboroto. Ideal para aprendices que están aprendiendo lo básico, así como para veteranos que buscan la sensación y el rendimiento de una máquina de bobina sólida.

Especificaciones del revestimiento:
- Marco de hierro dúctil fundido en arena
- Acabado de óxido rojo caballo de batalla
- Hardware de caballo de batalla estándar
- Bobinas de producción de 6 envolturas de 1.125"
- Máquina de armazón largo que permite un espacio entre los puntos de los revestimientos, con un recorrido largo
- Una herramienta para delinear todo alrededor... perfecta para esos largos días de noquear tatuajes flash con velocidad y precisión.
- Funcionamiento 130-135 Hz a 6,5 ​​voltios descargados
- Empuja 3s a 11s Fácil
- Con un peso de 7.5 oz
- FABRICADO EN EE. UU.