NEW Dan Kubin MCi (Mini Cranker with Impact)!

Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.

Specs:

• Steel Frame with HD Seafoam Powder Coat Finish
  
• Weighted Brass Armature
• Deluxe Kubin Components including DK Thumbs and updated Slide Vise

Setup / Usage:

• Works well with Standard Needle on Bar AND with Cartridges
• Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
• This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
• Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
• Higher voltage between 5 - 7 Volts for most Lining
• Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
• Polarity is not crucial, but will run slightly more efficiently with Positive Down
• The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
• Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.  
• Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact. 

Use and Care:

• Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
  
• After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings.  DO NOT FILL THE MOTOR WITH OIL!!
• Keep sterilants away from all moving and electrical components!
• Sterilants are corrosive and will damage your machine if used carelessly.

Enjoy!

NEW Dan Kubin MCi (Mini Cranker with Impact)!

Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.

Specs:

• Steel Frame with 24k Gold Plated Frame and Hardware
  
• Weighted Brass Armature
• Deluxe Kubin Components including DK Thumbs and updated Slide Vise

Setup / Usage:

• Works well with Standard Needle on Bar AND with Cartridges
• Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
• This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
• Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
• Higher voltage between 5 - 7 Volts for most Lining
• Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
• Polarity is not crucial, but will run slightly more efficiently with Positive Down
• The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
• Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.  
• Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact. 

Use and Care:

• Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
  
• After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings.  DO NOT FILL THE MOTOR WITH OIL!!
• Keep sterilants away from all moving and electrical components!
• Sterilants are corrosive and will damage your machine if used carelessly.

Enjoy!

DK Offset Cartridge Grip! 

The offset helps put the machine over the top of the user’s hand, making it more ergonomic and easier to keep the machine upright when pulling those large square looking lines.

• TWO Versions Available: 
  
  • Heavy Weight 1.25" BRASS Grip and Stainless Steel backstem (8oz)
  • Feather Weight 1.25" ALUMINUM Grip and Stainless Steel backstem (2.75oz)
• Brass is heavier but absorbs vibration more and offsets the pull of a clip cord and or any ass end tattoo machine weight, balancing more over the hand
• Aluminum is much lighter and pairs well with use of a battery to reduce overall weight. Balance is a bit better with the Brass version, but it is a trade off for weight. 
• Offset for better balance and visibility 
• Made of naturally anti-microbial Brass
• Each Grip Comes with 5 Cartridge Drive Bars
• Please cover with barrier film for extra protection!
• Made in the USA by Dan Kubin 

Better tools to make better tattoos.

Workhorse Model 6 Liner

Formerly built by Marv Lerning, this is an updated and modernized version of Marv's 6 Liner inspired by the Waters Model 6 Frame. Now with updated geometry for more power and efficiency, plus swing gate vise added to guarantee ease of use with any and all tubes. 

We are stoked to release this new Workhorse Model built in house by our highly trained and knowledgeable machine techs. Bringing us back to our roots with an affordable base model machine made with shared parts and technology to reduce costs. We offer lots of limited and custom high-end machines these days and wanted to release a new base model option at base model pricing.

Specs:

• Full Size Frame milled in house from a solid block of Ductile Iron
• HD Flat Black Powder Coat Finish
• Deluxe Workhorse Hardware with Black Oxide Finish
• Swing Gate Steel Vise
• Custom 8 Wrap 1" Coils with 1/4" Steel Yoke 
• High End Specialty Steel Springs
• Solid Copper Contact with Allen Key Insert
• Reverse Rear Binder Setup with frame ground on coil deck
• Long Stroke with a solid hit great for 5s to 14s
  
• Medium Speed, running around 135-140 unloaded @ 6.5 Volts
• 6.5 Ounce Weight
• Made in the USA

Workhorse Model 6 Shader

Formerly built by Marv Lerning, this is an updated and modernized version of Marv's 6 Shader inspired by the Waters Model 6 Frame. Now with updated geometry for more power and efficiency, plus swing gate vise added to guarantee ease of use with any and all tubes. 

We are stoked to release this new Workhorse Model built in house by our highly trained and knowledgeable machine techs. Bringing us back to our roots with an affordable base model machine made with shared parts and technology to reduce costs. We offer lots of limited and custom high-end machines these days and wanted to release a new base model option at base model pricing.

Specs:

• Full Size Frame milled in house from a solid block of Ductile Iron
• HD Flat Black Powder Coat Finish
• Deluxe Workhorse Hardware with Black Oxide Finish
• Swing Gate Steel Vise
• Custom 8 Wrap 1.25" Coils
  
• High End Specialty Steel Springs
• Solid Copper Contact with Allen Key Insert
• Reverse Rear Binder Setup with frame ground on coil deck
• Long Stroke with a solid hit great for 5s to 15s
  
• Medium Speed, running around 105-110 unloaded @ 6.5 Volts
• 6.5 Ounce Weight
• Made in the USA

Dan Kubin X Adam Ciferri Ghost Dog Revival V2 - Distressed Purple

This is the new updated and improved version of the DK x AC Ghost Dog Revival. V2 features an upgraded slide vise guaranteed to easily work with any and all tubes, an opened up geometry for better function, performance, and power. Everything else is the same, just dialed in a little more to make it a little better :)

"Since working with Workhorse Irons, I have been given the opportunity to remaster my Revival machine, but being able to merge it into the platform of Adam Ciferri’s Ghostdog.

Thanks - Dan.

Dan Kubin X Adam Ciferri Ghost Dog Revival V2 Machine Specs:

• CNC Iron Frame designed in collaboration by Dan Kubin and Adam Ciferri
• Light Pink + Hot Pink + Purple Illusion HD Powder Coat Finish with Custom Matching Coil
  
• 24k Gold Plated Deluxe DK Hardware and Specialty Spring
• Hinge / Compression machine functionality eliminating any rear spring issues or breakage
• Machine comes setup for use as a slow or medium speed Liner. Also works well as a quick Shader if you turn down the volts a little. To easily change to a slow and punchy color packer, simply remove the backer spring under the front spring.
• Tuned for all-day, every-day street shop and/or custom tattooing
•  Medium speed with enough hit to easily push 3 to 18 Rounds and up to 49 mag
  
• Runs 125-130 Hz @ 6 Volts Unloaded, crank up to 8-10 Volts for large groupings
• CNC Cut Iron with the highest precision and care
• Mini-Size frame with Custom AC x DK 1" Keg Coil for a larger range and less amperage
• Weighs 6 oz
• MADE IN THE USA

Machine Setup:

• Standard Needle on Bar: standard coil machine set up. Work well with our Thick Rubber Bands and Dan's Perfect Nipples, but also work with standard nipples/grommets.
• Cartridges: possible, but not highly recommended.

ReproFX Spirit™ Thermal Tattoo Transfer Papers are made for the professional artist from the highest quality materials to create the highest visibility purple dyes and best ripstop stencil sheets in the world.

• Compatible with all thermal printers
• Consistent, high quality images
• Skin safe & shelf-stable

Two sizes Available - 8.5" x 11" or 8.5" x 14"

Manufactured in the United States since 1948.

Dan Kubin X Adam Ciferri Ghost Dog Revival V2!

Updated and improved version of the DK x AC Ghost Dog Revival. V2 features an upgraded slide vise guaranteed to easily work with any and all tubes, an opened up geometry for better function, performance, and power. Everything else is the same, just dialed in a little more to make it a little better :)

"Since working with Workhorse Irons, I have been given the opportunity to remaster my Revival machine, but being able to merge it into the platform of Adam Ciferri’s Ghostdog.

Thanks - Dan.

Machine Specs:

• CNC Iron Frame designed in collaboration by Dan Kubin and Adam Ciferri
• Hinge / Compression machine functionality eliminating any rear spring issues or breakage
• Machine comes setup for use as a slow or medium speed Liner. Also works well as a quick Shader if you turn down the volts a little. To easily change to a slow and punchy color packer, simply remove the backer spring under the front spring.
• Tuned for all-day, every-day street shop and/or custom tattooing
•  Medium speed with enough hit to push 3's to 14's no problem
• Runs 125-130 Hz @ 6 Volts Unloaded, crank up to 9-10 Volts for large groupings
• CNC Cut Iron with the highest precision and care for superior conductivity
• Mini-Size frame with Custom AC x DK 1" Keg Coil for a larger range and less amperage
• Custom Rubbed Bronze Plated Finish
• Deluxe DK Black Hardware and Stainless Spring
• Weighs 6 oz
• MADE IN THE USA

Machine Setup:

• Standard Needle on Bar: standard coil machine set up. Work well with our Thick Rubber Bands and Dan's Perfect Nipples, but also work with standard nipples/grommets.
• Cartridges: possible, but not highly recommended.

NEW Dan Kubin V3/24 Sidewinder!

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

RCA Specifications:

• RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
• This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
• This will also work good with a right-angle RCA cord.
• Clip Cord option still works, it is just wired backwards.
• The position of the battery makes the machine’s balance point much more forward, like a pen.

Machine Specs:

• Verdigris Patina Plated Brass Frame with 24k Gold Plated Hardware and Motor Cover (*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.

NEW Dan Kubin V3/24 Sidewinder!

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

RCA Specifications:

• RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
• This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
• This will also work good with a right-angle RCA cord.
• Clip Cord option still works, it is just wired backwards.
• The position of the battery makes the machine’s balance point much more forward, like a pen.

Machine Specs:

• Verdigris Patina Plated Brass Frame with matching Verdigris Motor Cover (*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.

Dan Kubin Needle Bar Tensioner

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added Tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. 

The V3/24 Tensioner can be used on all versions of Dan Kubin V3Rs, 2019 to 2024. 

Needle Bar Tensioner Specifications:

• Lightweight Aerospace Aluminum Arm with precision made custom bearing
• Creates necessary needle bar tension for stability, eliminating the need to use a Rubber Band
• Moves forward and backwards, in and out of position easily by loosening and tightening the thumbscrew
• When setting up your needle and tube, position Needle Tensioner in desired position depending on the amount of tension you want to add to the needle bar. 
• Adjust position by loosening the thumbscrew, pull arm back and then tighten when you reach desired tension. 

Upgrade Step by Step: 

1. Loosen and remove the thumbscrew
2. Insert thumbscrew into hole in Needle Bar Tensioner
3. Re-insert thumbscrew into frame with Tensioner bearing facing inwards (see picture)
4. Ensure Vise Slide is in correct position so the thumbscrew easily threads into Slide
5. Tighten with Needle Bar Tensioner in desired position

**OG V3R and V3/23 SPECIAL NOTE - Use of this Tensioner instead of Rubber Bands will noticeably increase the strength of your machine. If it is hitting too hard using the Needle Bar Tensioner, simply adjust your voltage and turn the machine down and adjust stroke wheel setting as needed to accomplish desired speed / hit. 

NEW Dan Kubin V3/24 Sidewinder!

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

Machine Specs:

• Verdigris Patina Plated Brass Frame with matching Verdigris Motor Cover (*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.

New Mike Pike Smith & Howard Liner!

Milled with updated Mike Pike geometry in the shape of what is traditionally referred to as a Blackie frame for it's association with the tattoo artist Brooklyn Blackie. Many are under the presumption he was the originator of this design, but this frame shape was originally made by Smith & Howard Tattoo Supply in the early 1900s. 

• Mini Pike S&H Frame CNC Cut from Iron Bars
• Black Zinc Finish
• Deluxe Workhorse Blackened Hardware
• Long Fluted Armature Speed Bar
• Blackened Steel binding posts
• 1" 8 Wrap Workhorse Coils
• Medium Speed with a Long Stroke and Hard Hit
• Running 130-135 Hz Unloaded at 6.5 Volts
• Great for use with 5s to 14s
• Made in the USA by Mike Pike
• Comfortable and well balanced with a tube vice that will bite and hold all disposable and stainless tubes
• Forward facing wingnut that won't ride your hand or get in the way
• 6.4 ounce weight