Dan Kubin V3/24 Sidewinder!

Highlights:

• Polished Brass Frame with Black Hardware (*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 

• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.

RCA Specifications:

• RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
• This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
• This will also work good with a right-angle RCA cord.
• Clip Cord option still works, it is just wired backwards.
• The position of the battery makes the machine’s balance point much more forward, like a pen.

Description:

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan.  All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

Joshua Bowers High-Jack

The High-Jack attaches to your workstation magnetically and plugs in to the "machine" port on your power supply effectively moving your clip cord jack 5 feet into the air. This is the ideal position for your clip cord to hang from to keep it off the floor and free from rubbing, tugging, and snagging as you work.

• No more rolling over your cord with your chair
• Keep your cord off the floor
• Reduces the weight hanging off the back of the machine
• Reduces tugs and snags as you tattoo
• Extends the life of your clipcord

A few words from Joshua about The High-Jack:

"The High-Jack is a product I developed to make my clipcord drape and move more easily. The High-Jack magnetically attaches to your work station and plugs in to the Machine port on your power supply. Your clip cord then plugs in to the High-Jack, effectively lifting the clipcord jack 5 feet in to the air. This allows the cord to drape naturally from above you, doesn’t rub on the floor, doesn’t snag across your lap and it takes weight off of the back of the machine easing hand fatigue greatly.

The High-Jack Switch has all the great features of the basic High-Jack with the great new feature of having a switch box at the end to be able to toggle back and forth between two cords. This is a great feature for people using multiple cord types or just want two cords connected so they don’t have to switch cords back and forth. The toggle move from side to side selecting which cord is powered with off in the middle, so you can run on constant and turn your machine off at the High-Jack.

I have been using this product for over a year now, along with the rest of my shop. We were originally just testing them out but I speak for me and the rest of the shop when I say that we can’t imagine tattooing without them now."

Workhorse x Good Judy ECO Premium Needles on Bar

Tested and trusted, these pre-made Eco Conscious Tattoo Needles on Bar provide outstanding quality from WORKHORSE IRONS & GOOD JUDY INC. Their collaboration ensures a check of sustainability you can count on, certified by internationally-recognized third party organizations.

The packaging for these needles is completely unbleached, PFAS-free, compostable and recyclable, and is another step in our companies' commitment to environmental protection.

With more qc checks and heavier needle bars, this top-notch product is perfectly tailored for tattoo artists by tattoo artists, after 20 years of continuously improving their quality and configurations.

Specs:

• #12 Needles on all Traditional Groupings
• #10 Needles on all Tight Groupings / Bugpins
• Made with High Quality 316L Japanese Steel Needles plus Heavy Duty Thicker Needle Bars for greater stability 
• Easy open slide box
• All packaging is unbleached, PFAS free and compostable...even the needle trays and blister paper!
  

We have invested a year of effort and resources to ensure our needles and packaging meet the compostability standards of excellence. Although costly to create, we are proud of the superior results! We strive to offer more environmentally conscious tattoo products and diminish single use plastic while propelling eco-tattooing into ubiquity. This endeavor is yet another milestone toward our eco-friendly mission.

These new needles on bar are the best premium needles we have ever made. Not only are they eco friendly, they also outperform all needles we have tested!

*please let us know if we don't have any groupings you need and we will add them to the line up

KYŌDAI SOFT-TIP Brush Pen 

The Kyodai Brush Pen, also known as a fudepen (筆ペン), combines surgical-grade pigment with the flow and control of traditional fudepens. Its brush-like tip glides effortlessly across skin, giving artists smoother ink flow, better coverage, and precise control for calligraphy, freehand stencils, or detailed linework.

The SOFT-TIP felt brush pen boasts a supple and pliable tip made from a softer, more flexible felt material. This characteristic provides a smooth and fluid drawing experience, allowing the pen to adapt to varying pressure for expressive strokes. The soft felt tip enables a broader range of line thickness, making it well-suited for creating calligraphy and controlling line thickness.

Available in:

• Gentian Violet
• Tokyo Red 
• Golden Yellow
• Emerald Green
• Vermilion

KYŌDAI FIRM-TIP Brush Pen 

The Kyodai Brush Pen, also known as a fudepen (筆ペン), combines surgical-grade pigment with the flow and control of traditional fudepens. Its brush-like tip glides effortlessly across skin, giving artists smoother ink flow, better coverage, and precise control for calligraphy, freehand stencils, or detailed linework.

The FIRM-TIP felt brush pen features a sturdy, yet precise tip made of compressed and durable felt material. This provides a smooth and consistent flow of ink. The firmness of the tip allows for controlled and defined lines, making it well-suited for tasks that require precision with a consistent line thickness. The firm felt tip maintains its shape during use, ensuring reliability and accuracy in your creative endeavors. The firm tip offers a balance between control and fluidity.

Available in:

• Gentian Violet
• Tokyo Red
• Golden Yellow
• Emerald Green

Dan Kubin V3/24 Sidewinder!

Highlights:

• Black Brass Frame with Black Hardware (*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.

Description:

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

DK Offset Cartridge Grip! 

The offset helps put the machine over the top of the user’s hand, making it more ergonomic and easier to keep the machine upright when pulling those large square looking lines.

• TWO Versions Available: 
  
  • Heavy Weight 1.25" BRASS Grip and Stainless Steel backstem (8oz)
  • Feather Weight 1.25" ALUMINUM Grip and Stainless Steel backstem (2.75oz)
• Brass is heavier but absorbs vibration more and offsets the pull of a clip cord and or any ass end tattoo machine weight, balancing more over the hand
• Aluminum is much lighter and pairs well with use of a battery to reduce overall weight. Balance is a bit better with the Brass version, but it is a tradeoff for weight. 
• Offset for better balance and visibility 
• Made of naturally anti-microbial Brass
• Each Grip Comes with 5 pack of Cartridge Drive Bars
• Please cover with barrier film for extra protection!
• Made in the USA by Dan Kubin 

Better tools to make better tattoos.

 Dan Kubin V3/24 Sidewinder!

Highlights:

• Polished Brass Frame with Black Hardware(*Finish may vary)
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 and V7 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar:
  • Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension. 
  • Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples. 
    
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane 
  

Description:

The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine. 

Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency. 

The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder.  Hard hitting, effortless, and zippy.  -Intended for experienced artists who don’t want to mess around.

Made in the USA!

DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan.  All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.

Workhorse Model 6 Liner

Formerly built by Marv Lerning, this is an updated and modernized version of Marv's 6 Liner inspired by the Waters Model 6 Frame. Now with updated geometry for more power and efficiency, plus swing gate vise added to guarantee ease of use with any and all tubes. 

We are stoked to release this new Workhorse Model built in house by our highly trained and knowledgeable machine techs. Bringing us back to our roots with an affordable base model machine made with shared parts and technology to reduce costs. We offer lots of limited and custom high-end machines these days and wanted to release a new base model option at base model pricing.

Specs:

• Full Size Frame milled in house from a solid block of Ductile Iron
• HD Flat Black Powder Coat Finish
• Deluxe Workhorse Hardware with Black Oxide Finish
• Swing Gate Steel Vise
• Custom 8 Wrap 1" Coils with 1/4" Steel Yoke 
• High End Specialty Steel Springs
• Solid Copper Contact with Allen Key Insert
• Reverse Rear Binder Setup with frame ground on coil deck
• Long Stroke with a solid hit great for 5s to 14s
  
• Medium Speed, running around 135-140 unloaded @ 6.5 Volts
• 6.5 Ounce Weight
• Made in the USA

Workhorse Model 6 Shader

Formerly built by Marv Lerning, this is an updated and modernized version of Marv's 6 Shader inspired by the Waters Model 6 Frame. Now with updated geometry for more power and efficiency, plus swing gate vise added to guarantee ease of use with any and all tubes. 

We are stoked to release this new Workhorse Model built in house by our highly trained and knowledgeable machine techs. Bringing us back to our roots with an affordable base model machine made with shared parts and technology to reduce costs. We offer lots of limited and custom high-end machines these days and wanted to release a new base model option at base model pricing.

Specs:

• Full Size Frame milled in house from a solid block of Ductile Iron
• HD Flat Black Powder Coat Finish
• Deluxe Workhorse Hardware with Black Oxide Finish
• Swing Gate Steel Vise
• Custom 8 Wrap 1.25" Coils
  
• High End Specialty Steel Springs
• Solid Copper Contact with Allen Key Insert
• Reverse Rear Binder Setup with frame ground on coil deck
• Long Stroke with a solid hit great for 5s to 15s
  
• Medium Speed, running around 105-110 unloaded @ 6.5 Volts
• 6.5 Ounce Weight
• Made in the USA

Hustle Butter Numbing Spray (1.9 fl oz)

Artists, this one is for YOU! We took your feedback, we heard your needs, and we have the ULTIMATE in-process solution for you. Hustle Butter Numbing Spray, a dual-action anesthetic AND antiseptic cleanser, in an easy-to-use, convenient spray bottle. It’s as easy as spray, wash and comfort. More comfort for your clients during tattoo and piercing sessions means longer, more efficient sessions for you – a win-win in our book.

We’re talking maximum over-the-counter pain relief with this effective wash formulated with 4% lidocaine – perfect for temporarily numbing the area and soothing pain and itching. This best-in-class numbing wash is also made with skin-loving ingredients known to help calm skin, such as aloe leaf juice, green tea extract, witch hazel extract and chamomile. This product delivers EVERYTHING you need and more to wash and soothe the area, all while providing comfort to your client. A happier client = a better session. And better sessions mean better results. 

Key Features & Benefits:

• Dual-action anesthetic and antiseptic cleanser for use in-process to wash area and provide comfort
• Numbs area and provides temporary relief of pain and itching
• Cleans skin and helps prevent infection
• Made with vegan and cruelty free ingredients
• Easy-to-use spray bottle for maximum convenience

What's In It?

Active Ingredients: Lidocaine HCI 4.0% (Topical Anesthetic), Benzalkonium Chloride 0.10% (Antimicrobial)

Inactive Ingredients: Aloe Barbadensis Leaf Juice, Coceth-7, PPG-1-PEG-9 Lauryl Glycol Ether, PEG-40 Hydrogenated Castor Oil, Soytrimonium Chloride, Fragrance (Parfum), Propylene Glycol, Glycerin, Water (Aqua), Chamomilla Recutita (Matricaria) Flower Extract, Camellia Sinensis Leaf Extract, Arnica Montana Flower Extract, Hamamelis Virginiana (Witch Hazel) Leaf Extract, Symphytum Officinale Leaf Extract, Rosmarinus Officinalis (Rosemary) Oil, Methylchloroisothiazolinone, Methylisothiazolinone, Benzyl Benzoate, Citronellol, Coumarin, Geraniol, Hexyl Cinnamal, Hydroxycitronellal

How To Use:

• To open: Press button on back of cap, turn cap counter clockwise until you can press down where it says “Press” and you see nozzle in front.
• To use: Spray small amount onto clean skin before and during session as needed (do not exceed 3-4 times/day on same area). Allow a few minutes for numbing to kick in. Skin that has been sprayed may be covered with a sterile bandage but let area dry first.
• To close/lock: Turn cap clockwise until button pops out.

New DK Swift Tip System!  

This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your workstation. 

Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health. 

Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips! 

• 1" Brass Grip for use with DK Swift Tips

• Simply bag grip with designated bag and click Swift Tip into bagged grip for an improved tattoo experience

• 95% Less Plastic Waste than Disposable Plastic Tubes

• If bagged properly there is no reason to autoclave the grip

• Made in the USA by Dan Kubin 

Better tools to make better tattoos.

This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your workstation. 

Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health. 

Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips! 

DK Swift Tips - 5 to 11 Round - Box of 24 Tips (Grip Not Included)

*Must be used with DK Swift Tip Grip

These tips have great visibility and come to a nice point.  The biggest benefit is being able to see more needle even when you don't have a lot of needle hanging out.

The shape of the round tips is in between a round and a diamond. That said, it is the best of both worlds.  It allows for maximum versatility and stability for a wider range of sizes.

This tip configuration is for your medium round needle groupings.

I prefer it for my straight 5 rounds up to straight 9RL, or a tight or bug pin 11 Round. (if using a traditional 11 Round, I recommend the 9-18 size)

These tips are hydrophobic and have an antimicrobial additive in them. That said, you may need to check with your local health dept for protocol on single use plastic products used in the tattooing process. (such as ink caps)

*Blister packaged tips coming soon

Made in house at DK Rotary in Kansas City MO, USA

Better tools to make better tattoos.