Dan Kubin V3/24 Sidewinder - FEATHERWEIGHT Black Aluminum RCA
Regular price$755.00 USD
Dan Kubin V3/24 Sidewinder!
Highlights:
Black Polished Aluminum Frame with Blackened Hardware
Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.5 ounces
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.
Machine Setup:
Standard Needle on Bar:
Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension.
Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards.
The position of the battery makes the machine’s balance point much more forward, like a pen.
Description:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine.
Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency.
The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Dan Kubin V3/24 Sidewinder - FEATHERWEIGHT Black Aluminum CC
Regular price$730.00 USD
Dan Kubin V3/24 Sidewinder!
Highlights:
Black Polished Aluminum Frame with Blackened Hardware
Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.5 ounces
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short
Machine Setup:
Standard Needle on Bar:
Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension.
Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
Description:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine.
Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency.
The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Upgrade your experience with the Critical Connect V3 Battery. Enhanced with a 1.5” Color Display Screen and a larger 2000 mAH battery, enjoy extended duration and convenient session/run time mode.
With magnetic connection, the V3 Battery seamlessly connects directly to the Critical Torque Machine and the Bishop Power Wand. This versatile battery also includes an RCA converter, allowing for universal compatibility with any RCA machine.
FEATURES:
Longest running battery on the market with increased battery life
Larger, intuitive 1.5" color display
Controls for: voltage, jumpstart ON/OFF, hourly rate tracker, Run / Session timers, presets, bluetooth (Critical Connect) for FS compatibility, and ability to modify settings.
5 tactical buttons for easy navigation
Universal Compatibility with your favorite machines using the RCA Converter
SPECIFICATIONS:
Battery weight: 2.1 oz
Longest Running Battery in the Market (dependent on machine setup/voltage)
Manual/Instructions – QR code provided in with packaging
The main goal for this batch is for simple tuning, but with the option to dial it precisely for those who know how they want their machine to run. Considered by some to be the most revolutionary Sidewinder yet.
The v7.5 Sidewinder has the unique ability to allow users to adjust stroke length and hit independently. This means you can keep the stroke that works for you while playing with needle groupings, style, and skin types.
Highlights:
Deluxe 24k Gold plated frame with Black side plating
Deluxe Blackened Hardware
Impact screw and stroke length are now adjusted with the 1.5mm Allen key provided with the machine.
Straight angle on drive spring shelf on the armature bar, allowing for a more effortless and graceful hit.
More prominent timing marks on the side plate for the impact pin. (for advanced tuning/stroke adjustment, this helps with being more intuitive)
Crisp and clean acoustics, slightly quieter than other sidewinder models
Side locking screw is positioned to secure the impact screw most effectively
Specifications:
Forward, low and balanced weight of 6.2 oz
Recommended voltage range: 4 - 6.5
Great in the lower volt range for shading to color packing, fine line and stippled whip shading techniques.
It has 5 stroke positions ranging from 3.5-4mm. While tattooing, hit is controlled with adjustable return spring tension. If you want a softer hitting machine, you don’t have to compromise the stroke length.
The main goal for this batch is for simple tuning, but with the option to dial it precisely for those who know how they want their machine to run. Considered by some to be the most revolutionary Sidewinder yet.
The v7.5 Sidewinder has the unique ability to allow users to adjust stroke length and hit independently. This means you can keep the stroke that works for you while playing with needle groupings, style, and skin types.
Highlights:
Polished Nickle plated frame with Black side plating
Deluxe Blackened Hardware
Impact screw and stroke length are now adjusted with the 1.5mm Allen key provided with the machine.
Straight angle on drive spring shelf on the armature bar, allowing for a more effortless and graceful hit.
More prominent timing marks on the side plate for the impact pin. (for advanced tuning/stroke adjustment, this helps with being more intuitive)
Crisp and clean acoustics, slightly quieter than other sidewinder models
Side locking screw is positioned to secure the impact screw most effectively
Specifications:
Forward, low and balanced weight of 6.2 oz
Recommended voltage range: 4 - 6.5
Great in the lower volt range for shading to color packing, fine line and stippled whip shading techniques.
It has 5 stroke positions ranging from 3.5-4mm. While tattooing, hit is controlled with adjustable return spring tension. If you want a softer hitting machine, you don’t have to compromise the stroke length.
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added Tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power.
The V3/24 Tensioner can be used on all versions of Dan Kubin V3Rs, 2019 to 2024.
Needle Bar Tensioner Specifications:
Lightweight Aerospace Aluminum Arm with precision made custom bearing
Creates necessary needle bar tension for stability, eliminating the need to use a Rubber Band
Moves forward and backwards, in and out of position easily by loosening and tightening the thumbscrew
When setting up your needle and tube, position Needle Tensioner in desired position depending on the amount of tension you want to add to the needle bar.
Adjust position by loosening the thumbscrew, pull arm back and then tighten when you reach desired tension.
Upgrade Step by Step:
Loosen and remove the thumbscrew
Insert thumbscrew into hole in Needle Bar Tensioner
Re-insert thumbscrew into frame with Tensioner bearing facing inwards (see picture)
Ensure Vise Slide is in correct position, so the thumbscrew easily threads into Slide
Tighten with Needle Bar Tensioner in desired position
**OG V3R and V3/23 SPECIAL NOTE - Use of this Tensioner instead of Rubber Bands will noticeably increase the strength of your machine. If it is hitting too hard using the Needle Bar Tensioner, simply adjust your voltage and turn the machine down and adjust stroke wheel setting as needed to accomplish desired speed / hit.
Workhorse Irons
Dan Kubin V3/24 Sidewinder - Polished Brass CC
Regular price$720.00 USD
Dan Kubin V3/24 Sidewinder!
Highlights:
Polished Brass Frame with Black Hardware(*Finish may vary)
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.
Machine Setup:
Standard Needle on Bar:
Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension.
Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane
Description:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine.
Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency.
The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Polished Brass Frame with Black Hardware (*Finish may vary)
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.
Machine Setup:
Standard Needle on Bar:
Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension.
Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards.
The position of the battery makes the machine’s balance point much more forward, like a pen.
Description:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine.
Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency.
The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.
Machine Setup:
Standard Needle on Bar:
Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension.
Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards.
The position of the battery makes the machine’s balance point much more forward, like a pen.
Description:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine.
Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency.
The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
Black Brass Frame with Black Hardware (*Finish may vary)
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. There are three lines on the stroke wheel…shortest line is for shortest stroke / smaller groupings, the 3/4 line is middle of the road for medium stroke / medium to large groupings, full line is long stroke for large grouping work. You can’t make it too long or too short, play with it and find the right setting for the work you are doing.
Machine Setup:
Standard Needle on Bar:
Needle Bar Tensioner - when setting up your needle and tube, position needle tensioner in desired position depending on the amount of tension you want to add to the needle bar. Adjust position by loosening the thumbscrew and then tightening when you reach desired tension.
Rubber Band alternative setup - Loosen / remove thumbscrew to take the needle tensioner off. Then when setting up the machine, wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
Description:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power. These machines can be used with or without the Tensioner, it is detached by simply removing the thumbscrew and taking it off the machine.
Aside from the added Needle Bar Tensioner, this new version of remastered V3 Sidewinder is dialed in and updated with various improvements to increase machine longevity and consistency.
The V3/24 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
Made in the USA!
DK Machines sold by Workhorse are engineered and designed by Dan. Parts are milled in his authorized and trusted machine shop, then assembled by DK certified trained technicians at the Workhorse facility in Michigan. All Sidewinders go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. All current Sidewinders are serviced by Workhorse, some older models are serviced by Dan or one of his certified technicians found on his website.
This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your workstation.
Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health.
Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips!
DK Swift Tips - 1 to 5 Round - Box of 24 Tips (Grip Not Included)
*Must be used with DK Swift Tip Grip
These tips have great visibility and come to a nice point. The biggest benefit is being able to see more needle even when you don't have a lot of needle hanging out.
The shape of the round tips is in between a round and a diamond. That said, it is the best of both worlds. It allows for maximum versatility and stability for a wider range of sizes.
This tip configuration is for your smaller round needle groupings.
I prefer it for my singles to 5's, and even tight or bug pin 7's.
These tips are hydrophobic and have an antimicrobial additive in them. That said, you may need to check with your local health dept for protocol on single use plastic products used in the tattooing process. (such as ink caps)
*Blister packaged tips coming soon
Made in house at DK Rotary in Kansas City MO, USA
Better tools to make better tattoos.
Workhorse Irons
DK Swift Tips - 5 to 11 Round (Box of 24 Tips)
Regular price$28.00 USD
This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your workstation.
Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health.
Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips!
DK Swift Tips - 5 to 11 Round - Box of 24 Tips (Grip Not Included)
*Must be used with DK Swift Tip Grip
These tips have great visibility and come to a nice point. The biggest benefit is being able to see more needle even when you don't have a lot of needle hanging out.
The shape of the round tips is in between a round and a diamond. That said, it is the best of both worlds. It allows for maximum versatility and stability for a wider range of sizes.
This tip configuration is for your medium round needle groupings.
I prefer it for my straight 5 rounds up to straight 9RL, or a tight or bug pin 11 Round. (if using a traditional 11 Round, I recommend the 9-18 size)
These tips are hydrophobic and have an antimicrobial additive in them. That said, you may need to check with your local health dept for protocol on single use plastic products used in the tattooing process. (such as ink caps)
*Blister packaged tips coming soon
Made in house at DK Rotary in Kansas City MO, USA
Better tools to make better tattoos.
Workhorse Irons
DK Swift Tips - 7 Mag (Box of 24 Tips)
Regular price$28.00 USD
New DK Swift Tip System!
This is a new and convenient way to use standard needles with a metal grip to maintain the rigid feel and counterweight of a steel tube. If setup correctly, this system allows for a proper barrier from cross contamination without use of an autoclave. It is still recommended to wipe the grip with a sterilant between uses as you would your workstation.
Quick and easy setup for standard needle on bar use with much less vibration than standard disposable tubes. Less vibration means less harm to your hands, tendons, and overall body stress for greater longevity and health.
Utilizing a metal grip and small click in plastic tips, this system creates much less waste...about 95% less plastic than most disposable grips!
DK Swift Tips - 7 Mag - Box of 24 Tips (Grip Not Included)
*Must be used with DK Swift Tip Grip
These tips have great visibility and come to a nice point. The biggest benefit is being able to see more needle even when you don't have a lot of needle hanging out.
The shape of the mag tip allows for mor visibility at the end of the tip. The side wall is beveled back so there is no excess material on the edges. This allows for getting a more precise "cut in" near lines and tight spaces.
Fits 7 mags.
These tips are hydrophobic and have an antimicrobial additive in them. That said, you may need to check with your local health dept for protocol on single use plastic products used in the tattooing process. (such as ink caps)
