Dan Kubin Replacement Accessory Kit includes the following:

• 1.5MM Allen Key
• 5/64" Hex Key
• Taper Pin (used to open up/ensure your needle bar loop is the correct size)
  
• Dan Kubin Universal Sidewinder Spring
• 20 Dan Kubin Perfect Nipples

High Quality US Made blue tempered spring steel, precision cut in two lengths with slotted rear for universal fit.

Available in either 18 or 20 Gauge thickness.

Specs:
- Short : 0.50" width x 1.45" length
- Long : 0.50" width x 1.69" length

Limited Deluxe Seth Ciferri Mini Fastback Liner/Shader Kits!

This machine kit comes with parts to build as either a liner or a shader. Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Mini Fastback Frame
• Black Zinc Finish
• Deluxe Blackened Hardware
• Spring Loaded Swing Gate Vise
• 1" 8 Wrap Custom Soldered Coils
• Liner and Shader Armature Bar
  
• 4 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included
• Weighs 7.2 oz

Liner typical specs:

• Medium Slow Speed with a Medium Hard Hit
• Running 125-130 Hz @ 6 V Unloaded
• Pushing 5's to 11's No Problem

Shader typical specs:

• Medium Speed with a Hard Hit
• Running 105-110 Hz @ 6 V Unloaded
• Pushing up to 13's Easy

Comes with or without our Armature Bar Fixture. We recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness.

Made in the USA.

Limited Deluxe Chris Smith Carnivore Liner Kit

Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Carnivore Frame
• Black Zinc Finish
• Deluxe Blackened Hardware
• 1.25" 6 Wrap Custom Soldered Coils
• 2 Liner Armature Bar Options
  
• 4 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included
• Weighs 6.8 oz

Liner typical specs:

• Pushes 5’s to 11’s Easy
• Running Slower and Harder
• 130-135Hz at 6.5 V unloaded

*Comes with the tools you need to build the machine except an Armature Bar Fixture. We highly recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness. You can find one here in our Tool Category

Made in the USA.

Limited Deluxe Chris Smith Supreme Liner Kit!

Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Aluminum Frame
• Steel Base and Vise Inlaid into the Aluminum Frame
• Deluxe Blackened Steel Hardware, Spring Saddle, and Clip Cord Yoke Screw
  
• 6 Wrap 1.25” Soldered Coils
  
• Liner Armature Bar
  
• 4 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches (you will need a flat head screw driver though)
  
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included
• Weighs 5.6 oz

Liner typical specs:

• Pushes 5’s to 14’s Easy
• Long Stroke, Medium Speed with a Heavy Hit
  
• 130-135 Hz at 6.5 V unloaded

Comes with or without our Armature Bar Fixture. We recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness.

Made in the USA.

Limited Deluxe Chris Smith Hater Liner Kit

Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Carnivore Frame
• Black Zinc Finish
• Deluxe Blackened Hardware
• 1" 8 Wrap Custom Soldered Coils
• 2 Liner Armature Bar Options
• 2 Liner Armature Bar Options
  
• 4 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches (you will need a flat head screw driver though)
  
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included
• Weighs 5.6 oz

Liner typical specs:

• Pushes 5’s to 11’s Easy
• Long Stroke, Medium Speed with a Heavy Hit
  
• 130-135 Hz at 6.5 V unloaded

*Comes with the tools you need to build the machine except an Armature Bar Fixture. We highly recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness. You can find one here in our Tool Category

Made in the USA.

Limited Adam Ciferri Bulldog Shader Kit

Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Bulldog Frame
• Black Zinc Finish
• Deluxe Blackened Hardware
• 1.25" 8 Wrap Custom Soldered Coils with 47 Cap
  
• Long Nipple Armature Bar
  
• 2 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included

Adam Ciferri Cast Iron Bulldog Shader Specs when he builds them:

- Tuned for all-day, every-day street shop and/or custom tattooing
- Solid hit that easily pushes 5-15 Mag Groupings
- Runs 95-105Hz @ 6.5 Volts Unloaded

*Comes with the tools you need to build the machine except an Armature Bar Fixture. We highly recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness. You can find one here in our Tool Category

Made in the USA.

Dan Kubin Weighted Impact Screw Kit

"New updated weighted impact screw! I found that it helps with the stability of the hit, and improved overall performance. Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band."

Thanks - Dan

Weighted Impact Kit Specifications:

• Upgrade for Dan Kubin V3R with updated armature bar (Late 2019 to 2022)
  
• Custom heat treated tool steel RHC 60 plus o-ring
• Easy swap out to increase the hit while improving the overall feel and sound
• Kit also includes both the 1.5mm and 2mm L wrench

Upgrade Step by Step: (see pictures for guidance)

1. Use the 1.5mm wrench to loosen the set screw on the side of the armature bar. Half a turn should loosen it enough to easily remove the impact screw.
2. Hold down the armature bar and use the 2mm wrench to remove the old impact screw.
3. Once removed, use the 1.5mm wrench to insert and tighten the weighted impact screw down until the o-ring starts to bulge out as it makes contact with the top of the armature.
4. Tuning - this is the most important step and will effect the timing and stroke of your machine.
1. While holding the armature bar down, roll the cam back until it makes contact with the vertical spring and gently stops. In this position the timing mark on the cam should align with the center of the timing mark on the frame.
2. If the timing mark on the cam is on the low side of the timing mark on the frame, tighten the weighted impact a little until it raises up to the center of the timing mark on the frame.
3. If the timing mark on the cam is on the high side, the impact is too far in and needs to be backed out (loosened) until the timing mark on the cam is in the center of the timing mark on the frame.
5. Use the 1.5mm wrench to tighten the set screw on the side of the armature bar.
6. Your machine is now upgraded and ready to use. One note would be that the new impact works well with the rubber band pulled slightly higher on the needle bar so it is perpendicular when the armature is in the down position.

Nickel Plated Limited Adam Ciferri Bulldog Shader Kit

Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Bulldog Frame
• Nickel Plated Finish
• Deluxe Blackened Hardware
• 1.25" 8 Wrap Custom Soldered Coils with 47 Cap
  
• Long Nipple Armature Bar
  
• 2 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included

Adam Ciferri Cast Iron Bulldog Shader Specs when he builds them:

- Tuned for all-day, every-day street shop and/or custom tattooing
- Solid hit that easily pushes 5-15 Mag Groupings
- Runs 95-105Hz @ 6.5 Volts Unloaded

*Comes with the tools you need to build the machine except an Armature Bar Fixture. We highly recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness. You can find one here in our Tool Category

Made in the USA.

Limited Deluxe SOBA Mini Rusto Liner/Shader Kit!

This machine kit comes with parts to build as either a liner or a shader. Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Mini Rusto Frame
• Black Zinc Finish
• Deluxe Blackened Hardware
• Spring Loaded Swing Gate Vise
• 1" 8 Wrap Custom Soldered Coils
• Liner and Shader Armature Bars
  
• 4 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included
• Weighs 6.8 oz

Liner typical specs:

• Very Light and Quick with a Solid Hit
• Great for Smaller to Medium Sized Groupings
• Pushing 3's to 9's easy
• Running 140-145 Hz @ 6.5 V Unloaded

Shader typical specs:

• Medium Quick Speed with a Solid Hit
• Pushing 5's to 13's easy
• Great for Packing in Solid Color, turn down a bit for Color Blends and Whip Shading
• Running 110-115 Hz @ 6.5 V Unloaded

Comes with or without our Armature Bar Fixture. We recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness.

Made in the USA.

Model 6 Liner Frame

• CNC Cut Iron Liner Frame
  
• Designed by Marv Lerning, inspired by the classic Waters Model 6
• Black Zinc Finish
• Geometry for 1.25" Coils
• Standard Pinch Vise
• Weighs 2.9 oz

Made in the USA

Model 6 Shader Frame

• CNC Cut Iron Shader Frame
  
• Designed by Marv Lerning, inspired by the classic Waters Model 6
• Black Zinc Finish
• Geometry for 1.25" Coils
• Standard Pinch Vise
• Weighs 3.10 oz

Made in the USA

Limited Deluxe Seth Ciferri Mini Flatside Liner/Shader Kits!

This machine kit comes with parts to build as either a liner or a shader. Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut ALUMINUM Mini Flastside Frame
• Lightly Distressed Black Zinc Finish
• Deluxe Blackened Hardware
• Front Loading Guillotine Vise
• 1" 8 Wrap Custom Soldered Coils
• Liner and Shader Armature Bar
  
• 4 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches
• Washer Package including all washers needed (steel, fiber, and shims)
• Alignment Tool included
• Weighs 6 oz

Liner typical specs:

• Medium Slow Speed with a Medium Hard Hit
• Running 130-135 Hz @ 6 V Unloaded
• Pushing 5's to 11's No Problem

Shader typical specs:

• Medium Speed with a Hard Hit
• Running 105-110 Hz @ 6 V Unloaded
• Pushing up to 13's Easy

Comes with or without our Armature Bar Fixture. We recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness.

Made in the USA.

Workhorse A1 Slideback Tattoo Machine Frame

• CNC Cut Iron Frame
  
• Designed by Mike Pike, modeled off a classic A1 Tattoo Machine
  
• Raw Finish ready for paint, powder coat, plating or oxide
  
• Geometry for 1.25" Coil Liner or Shader
  
• Swing Gate Vise with extra screws to work with 1.25" coils or with a yoke and 1" coils
  
• Weighs 2.8 oz

Frame and Swing Gate Vise parts only, no other parts or tools included.

Made in the USA

*Special Edition Black Friday Machine Kit at special pricing! Never before offered Zephyr Tattoo Machine Kits, plus optional armature bar fixture!

Cory Rogers Zephyr Liner Machine Kit

Kit includes all parts needed to build a great tattoo machine...but, it does not include the skills to build a great tattoo machine, sorry not sorry :)

• CNC Cut Iron Zephyr Frame
• Blackend Finish
• Deluxe Blackened Hardware
• 1" 8 Wrap Custom Soldered Coils
• Liner Armature Bar
  
• 2 Spring Sets with each kit
  
• All Screws you'll need PLUS necessary wrenches (you will need a flat head screw driver though)
  
• Washer Package including all washers needed (steel, fiber, and shims)

Liner typical specs:

• Medium Fast Speed with a Solid Hit
• Great Liner for Traditional Work
• 135-140Hz. @ 6.5 V unloaded
• Pushes 5s to 11s Easy
• Weighs 6.75 oz

*Comes with or without our Armature Bar Fixture. We recommend picking one up if you do not have one, it is by far the best way to assemble your armature bar and springs with proper alignment and tightness.

Made in the USA.