Black on Black version of Juan's classic OG Liner.
CNC Cut Iron Frame
HD Custom Black Finish
Deluxe Black Hardware
1.25" 6 Wrap Standard Electrical Tape Coils
Swing Gate Vise Guaranteed to lock tight on any tube
Medium Speed with a Solid Hit
140-145 Hz at 6.5 V Unloaded
Weighs 7.2 Ounces
Pushing 3-11's Easy
Workhorse Irons
Juan Puente Black on Black OG Shader
Regular price$380.00 USD
Juan Puente OG Shader
Black on Black version of Juan's classic OG Liner.
CNC Cut Iron Frame
HD Custom Black Finish
Deluxe Black Hardware
1.25" 8 Wrap Standard Electrical Tape Coils
Swing Gate Vise Guaranteed to lock tight on any tube
Slow Speed with a Solid Hit
110-115 Hz at 6 V Unloaded
Weighs 7.2 Ounces
Pushing up to 13's All Day
Workhorse Irons
Juan Puente OG Liner
Regular price$330.00 USD
Juan Puente OG Liner
The day has finally come...we now have a Juan Puente Workhorse model! Still built and tuned by Juan, these machines are cnc cut instead of welded and have the standard basic Workhorse finishing touches.
CNC Cut Iron Frame
Workhorse Red Oxide Finish
Deluxe Black Hardware
1.25" 6 Wrap Standard Heat Shrink Coils
Swing Gate Vise Guaranteed to lock tight on any tube
Medium Speed with a Solid Hit
135-140 Hz at 6.5 V Unloaded
Weighs 7.2 Ounces
Pushing 3-11's Easy
Workhorse Irons
Juan Puente OG Shader
Regular price$330.00 USD
Juan Puente OG Shader
The day has finally come...we now have a Juan Puente Workhorse model! Still built and tuned by Juan, these machines are cnc cut instead of welded and have the standard basic Workhorse finishing touches.
CNC Cut Iron Frame
Workhorse Red Oxide Finish
Deluxe Black Hardware
1.25" 8 Wrap Standard Heat Shrink Coils
Swing Gate Vise Guaranteed to lock tight on any tube
Slow Speed with a Solid Hit
100-105 Hz at 6 V Unloaded
Weighs 8 Ounces
Pushing up to 13's All Day
Workhorse Irons
Juan Puente Springs
Regular price$6.00 USD
Grouping
Price
Inventory
Quanity
Liner
$6.00 USD
Available
Shader
$6.00 USD
Available
Each Spring Set Includes: Fully punched front and rear springs.
Liner Spring Set- Juan Puente Liner (Medium Front, Short Rear) Shader Spring Set- Juan Puente Shader (Long Front, Short Rear)
Workhorse Irons
KN95 Face Masks
Regular price$20.00 USD
Grouping
Price
Inventory
Quanity
20 Masks
$20.00 USD
Available
60 Masks
$55.00 USD
Sold Out
KN95 Face Mask (Sealed Packs of 20)
Active carbon high-filtration mask with 5 layers
Up To 50 Times Protection Against Non-Toxic Dusts, Fibres & Aqueous Mists
High filtration efficiency and low breathing resistance
Adjustable nose clip
Easy To Store Due To Fold Flat design
*Not intended for medical use. So please, DO NOT purchase face masks with the false understanding they are 100% effective preventing infection from the Coronavirus. They are more about protecting others to reduce spread.
**Due to the personal hygiene nature of the product, face masks are non-returnable.
COVID-19 UPDATES:
We are shipping daily and have now expanded our requirements to include Medical Professionals. We still do not sell to at home tattooers but gladly sell to any medical professionals that need supplies. You are top priority, thank you for all you do!
Based on the guidelines from the Centers for Disease Control, we are taking all measures to ensure there is no contamination of our packages.
Due to the ongoing pandemic, manufacturers have drastically increased the cost of all PPE, masks included. We are working hard to keep these costs down, keep PPE in stock, and find other sources to provide better options with better pricing.
Stable Color
Lavender- 2 oz
Regular price$15.00 USD
Lavender - 2 oz. Twist Top Bottle
Stable Color Traditional Pigment is a powder pigment based ink, it is a bit thicker and based off traditional recipes that have been used to mix ink for years. If you know how to tattoo with a thicker powder pigment based ink, you will be stoked, it's super opaque and heals out bright, and can be cut down a bit if need be.....if you don't know how to tattoo with thicker pigment, we recommend trying our Eternal Inks.
Stable Color Inks have been researched and field tested to ensure quality and workability. The vehicle is made up of distilled water, 99.9% pure glycerin (vegan safe), and 99% ISP alcohol - No Surprises or Extra Ingredients. From bright solid fields, to pastel hues, to muted painterly tones. These inks are formulated for maximum flexibility, achieving the results you desire. MADE IN THE USA
*Now Standard with New Labels that include a Full Ingredient List, Batch Number, and Expiration Date.
Workhorse Irons
Legacy Edition Dan Kubin Antique Nickel V3R Sidewinder
Regular price$795.00 USDSale price$720.00 USD
*Spring Sale $75 off Limited Time Only*
Legacy Edition Dan Kubin V3R Sidewinder
*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.
"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.
Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
Antique Nickel Plated Brass Frame (*Finish may vary)
Black DK Thumbscrew and Blackened Brass OG Armature Bar
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
Legacy Edition Dan Kubin Black Brass V3R Sidewinder
Regular price$735.00 USDSale price$660.00 USD
*Spring Sale $75 off Limited Time Only*
Legacy Edition Dan Kubin V3R Sidewinder
*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.
"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.
Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
Black Oxide Brass Frame (*Finish may vary)
Black DK Thumbscrew and Polished Brass OG Armature Bar
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
Legacy Edition Dan Kubin Featherweight Black ALUMINUM V3R Sidewinder
Regular price$735.00 USDSale price$660.00 USD
*Spring Sale $75 off Limited Time Only*
Legacy Edition Dan Kubin V3R Sidewinder
*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.
"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.
Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
Black Anodize Polished Aerospace Aluminum Frame (*Finish may vary)
Black DK Thumbscrew and Polished Brass OG Armature Bar
Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.5 ounces
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
Legacy Edition Dan Kubin Featherweight Polished ALUMINUM V3R Sidewinder
Regular price$725.00 USDSale price$650.00 USD
*Spring Sale$75off Limited Time Only*
Legacy Edition Dan Kubin V3R Sidewinder
*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.
"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.
Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
Polished Aerospace Aluminum Frame (*Finish may vary)
Black DK Thumbscrew and Polished Brass OG Armature Bar
Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.5 ounces
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.
"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.
Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
24k Gold Plated Brass Frame (*Finish may vary)
Black DK Thumbscrew and Blackened Brass OG Armature Bar
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
Legacy Edition Dan Kubin Polished Brass V3R Sidewinder
Regular price$725.00 USDSale price$675.00 USD
*Spring Sale $50 off Limited Time Only*
Dan Kubin V3R Sidewinder
*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.
"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.
Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
Raw Polished Brass Frame (for an earned natural patina it will gain over time and use)
Black DK Thumbscrew and Polished Brass OG Armature Bar
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
Stable Color Traditional Pigment is a powder pigment based ink, it is a bit thicker and based off traditional recipes that have been used to mix ink for years. If you know how to tattoo with a thicker powder pigment based ink, you will be stoked, it's super opaque and heals out bright, and can be cut down a bit if need be.....if you don't know how to tattoo with thicker pigment, we recommend trying our Eternal Inks.
Stable Color Inks have been researched and field tested to ensure quality and workability. The vehicle is made up of distilled water, 99.9% pure glycerin (vegan safe), and 99% ISP alcohol - No Surprises or Extra Ingredients. From bright solid fields, to pastel hues, to muted painterly tones. These inks are formulated for maximum flexibility, achieving the results you desire. MADE IN THE USA
*Now Standard with New Labels that include a Full Ingredient List, Batch Number, and Expiration Date.
Stable Color
Light Brown- 2 oz
Regular price$15.00 USD
Light Brown - 2 oz. Twist Top Bottle
Stable Color Traditional Pigment is a powder pigment based ink, it is a bit thicker and based off traditional recipes that have been used to mix ink for years. If you know how to tattoo with a thicker powder pigment based ink, you will be stoked, it's super opaque and heals out bright, and can be cut down a bit if need be.....if you don't know how to tattoo with thicker pigment, we recommend trying our Eternal Inks.
Stable Color Inks have been researched and field tested to ensure quality and workability. The vehicle is made up of distilled water, 99.9% pure glycerin (vegan safe), and 99% ISP alcohol - No Surprises or Extra Ingredients. From bright solid fields, to pastel hues, to muted painterly tones. These inks are formulated for maximum flexibility, achieving the results you desire. MADE IN THE USA
*Now Standard with New Labels that include a Full Ingredient List, Batch Number, and Expiration Date.