Dan Kubin Weighted Impact Screw Kit

"New updated weighted impact screw! I found that it helps with the stability of the hit, and improved overall performance. Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band."

Thanks - Dan

Weighted Impact Kit Specifications:

• Upgrade for Dan Kubin V3R with updated armature bar (Late 2019 to Current)
  
• Custom heat treated tool steel RHC 60 plus o-ring
• Easy swap out to increase the hit while improving the overall feel and sound
• Kit also includes both the 1.5mm and 2mm L wrench

Upgrade Step by Step: (see pictures for guidance)

1. Use the 1.5mm wrench to loosen the set screw on the side of the armature bar. Half a turn should loosen it enough to easily remove the impact screw.
2. Hold down the armature bar and use the 2mm wrench to remove the old impact screw.
3. Once removed, use the 1.5mm wrench to insert and tighten the weighted impact screw down until the o-ring starts to bulge out as it makes contact with the top of the armature.
4. Tuning - this is the most important step and will effect the timing and stroke of your machine.
1. While holding the armature bar down, roll the cam back until it makes contact with the vertical spring and gently stops. In this position the timing mark on the cam should align with the center of the timing mark on the frame.
2. If the timing mark on the cam is on the low side of the timing mark on the frame, tighten the weighted impact a little until it raises up to the center of the timing mark on the frame.
3. If the timing mark on the cam is on the high side, the impact is too far in and needs to be backed out (loosened) until the timing mark on the cam is in the center of the timing mark on the frame.
5. Use the 1.5mm wrench to tighten the set screw on the side of the armature bar.
6. Your machine is now upgraded and ready to use. One note would be that the new impact works well with the rubber band pulled slightly higher on the needle bar so it is perpendicular when the armature is in the down position.

Dan Kubin Replacement Accessory Kit includes the following:

• 1.5MM Allen Key
• 5/64" Hex Key
• Taper Pin (used to open up/ensure your needle bar loop is the correct size)
  
• Dan Kubin Universal Sidewinder Spring
• 20 Dan Kubin Perfect Nipples

Workhorse Black/Navy Rubber Bands

Specs:
- Band No. 12
- Length: 1-3/4"
- Width: 1/16"
- Gauge: 1/32"
- Platinum Crepe Grade
- Thin Rubber Bands come in 1/4 lbs bags (875 pieces), Thick Rubber Bands come in 1/4 lbs bags (350 pieces)

Official DK Thumbscrew - 8-32 Thread, Full 5/8" Length, compatible with most Kubin Vise Styles.

Workhorse Small O-Rings, ideal for use as spacers on Armature Bar nipples. Also applicable for use on Dan Kubin Sidewinder Armatures to silence them.

Softer than standard Buna-N O-rings for a better seal in low-pressure applications, these are also resilient and offer excellent tear resistance. They resist hydraulic oils and motor oil. These O-rings have a round profile and are suitable for a wide range of static and dynamic sealing applications.

5/64 ID, 13/64 OD. 50A Soft Durometer.

Available in 10 packs or 100 packs.

New Stainless Steel V3r Sidewinder Spring - New updated spring used on 2020 to current sidewinders. Slightly different shape with a flat rear end of the spring.

OG Sidewinder Spring - From the original V3R sidewinder (2019-2020). Used for both the pivoting and rear stoke spring.  Also can be used for v3, v4, and v5. Original rounded rear end of the spring.

Ghost Dog Revival Spring - For the Dan Kubin X Adam Ciferri Ghost Dog Revival. Stainless steel front and backer spring included.

Dan Kubin X Adam Ciferri Ghost Dog Revival POSTER:

• 18x24" Black Light poster designed by the incredibly talented and handsome Adam Hathorn
• Signed by Dan and Adam

Dan Kubin X Adam Ciferri Ghost Dog Revival Hybrid Machine Info:

"Since working with Workhorse Irons, I have been given the opportunity to remaster my Revival machine, but being able to merge it into the platform of Adam Ciferri’s Ghostdog.

Thanks - Dan.

POSTER:

• 18x24" Black Light poster designed by Adam Hathorn
• Signed by Dan and Adam

Dan Kubin V3R Sidewinder

*This is a special run of Sidewinders built with the original V3R Armature Bar for an even heavier hit and slightly different feel from the current version V3R.

"Special Legacy Edition Sidewinder with OG V3R Armature Bar and Springs on the newer updated frame with DK Thumbscrew included! These Legacy machines are a little quieter and geared more towards being effortless with a stronger hit off the tip. These Legacy machines are intended for experienced tattooers, their happy place is for 7-14 Liners.

Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.

These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly." 

Thanks for looking - Dan.

Machine Specs:

• Raw Polished Brass Frame (for an earned natural patina it will gain over time and use)
  
• Black DK Thumbscrew and Polished Brass OG Armature Bar
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6) **Special note, Legacy Edition machine timing marks are slightly off due to using the OG armature on the newer frames. Down stroke timing mark should sit just outside the timing mark on the high side. If you go much lower you will know as you will make contact with the top of the frame with the armature.
  

• Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short. Smaller number setting great for small groupings, large numbers large groupings. Machines are tuned and shipped on the 5 setting, some don't ever adjust this, some do, user preference.
  

Machine Setup:

• Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
  
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

*Completely black oxided.  *please note that the brass will peak though over time where it sees heavy wear, adding to its character.

For more info please watch the V3R Setup and Tuning Video:

Dan Kubin V3R Sidewinder

"Now with an updated weighted impact screw! I found that it helps with the stability of the hit, and improved overall performance. Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.

Previous updates to the V3R include adding the coveted DK thumbscrew, moving the impact screw (the most crucial and misunderstood tuning element) to the front end of the armature bar and added a hardened steel impact pin so the machine will be easier to reset, and will hold its tune much longer. I also used a few tricks from the V7 to reduce spitting and make it hit a bit more rigid on the low end and added the backer springs as well to prevent spring breakage.

These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly." 

Thanks for looking - Dan.

Machine Specs:

• Black Polished Aluminum Frame with Blackened Hardware
• Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.5 ounces
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
  
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

Machine Setup:

• Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
  
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.

For more info please watch the V3R Setup and Tuning Video:

Lightweight Clip Cord handmade in Spain by Noe Quintillan.

The most compact, lightweight, and versatile clip cord available. Designed and built to be a compact lightweight cord on Kubin machines, but also provide a universal fit on any clip cord setup. Simple and clean. Less is more.

Built in magnet. 5.9 feet long, 1.3 ounce weight with little to no pull.

Clip Cord to RCA Adapter handmade in Spain by Noe Quintillan.

The most compact, lightweight, and versatile clip cord to RCA adapter available. Designed and built to be a compact adapter for use specifically on Kubin machines, but also provide a universal fit on any clip cord setup.

Noe Quintillan Lightweight RCA Cord

Available with or without the Clip Cord to RCA Adapter.

The most compact, lightweight, and versatile RCA Cord and clip cord to RCA adapter available. Designed and built to be a compact adapter for use specifically on Kubin machines, but also provide a universal fit on any RCA machine and clip cord setup.

Handmade in Spain with the highest precision and care by Noe Quintillan.

Dan Kubin V3R Sidewinder 

"Now with an updated weighted impact screw! I found that it helps with the stability of the hit, and improved overall performance. Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.

Previous updates to the V3R include adding the coveted DK thumbscrew, moving the impact screw (the most crucial and misunderstood tuning element) to the front end of the armature bar and added a hardened steel impact pin so the machine will be easier to reset, and will hold its tune much longer. I also used a few tricks from the V7 to reduce spitting and make it hit a bit more rigid on the low end and added the backer springs as well to prevent spring breakage.

These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly." 

Thanks for looking - Dan.

Machine Specs:

• Limited Pink Powder Coated Brass Frames
  
• Blackened Parts
• Black Anodize Aluminum Motor Cover
  
• DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
  
• The renowned rotary liner.  Effortlessly sink any size line by just grazing the skin.
• The motor is the same as the  V2-V4 Sidewinder, which has proven the test of time.  It has been a favorite of the long time Sidewinder collectors.
• Vice-Lock that easily tightens on nearly any tube
• Great for all varieties of Line Work or as a Fast Shader/Packer
  
• Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)

• Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot.  You can’t make it too long or too short

• 3.5 Ounce Weight

Machine Setup:

• Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
  
• Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
  

For more info please watch the V3R Setup and Tuning Video: