Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!
Now with more versatility and ease of hit adjustment throughout the tattoo. It is more ergonomic, more reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary.
The focus of its design is to be more like a shader/packer that can also line well, whereas the Sidewinder is more of a liner that can shade. If you prefer more punch at a slower to medium speed, this is a great option. Excellent for fine line, black and grey, color packing with any size mag. Can drive 14 liners, if you prefer to “set the needle into the skin” whereas the Sidewinder prefers to have the needle floated across the skin.
The Remastered Mojobox has a numbered upstroke wheel (same as the V3r) which allows for a wide range of versatility throughout the hit once in the 5.3 and up voltage ranges. Simply turn the stroke wheel for a longer or shorter stroke. The 5 setting is middle of the road and what most people use. Turn up towards 9 for longer srtroke and down towards 1 for shorter stroke.
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive which is the nature of a cartridge.
Typical operating range: 4 - 6 volts, sweet spot for most is 5 Volts on the 5 setting.
Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!
Now with more versatility and ease of hit adjustment throughout the tattoo. It is more ergonomic, more reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary.
The focus of its design is to be more like a shader/packer that can also line well, whereas the Sidewinder is more of a liner that can shade. If you prefer more punch at a slower to medium speed, this is a great option. Excellent for fine line, black and grey, color packing with any size mag. Can drive 14 liners, if you prefer to “set the needle into the skin” whereas the Sidewinder prefers to have the needle floated across the skin.
The Remastered Mojobox has a numbered upstroke wheel (same as the V3r) which allows for a wide range of versatility throughout the hit once in the 5.3 and up voltage ranges. Simply turn the stroke wheel for a longer or shorter stroke. The 5 setting is middle of the road and what most people use. Turn up towards 9 for longer srtroke and down towards 1 for shorter stroke.
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive which is the nature of a cartridge.
Typical operating range: 4 - 6 volts, sweet spot for most is 5 Volts on the 5 setting.
Brass Frame with Purple HD Powder Coat Finish and 2 Tone Highlights.
Recientemente remasterizado después de 6 años desde su encarnación, esta es la segunda generación de Mojobox. Ahora con más versatilidad y facilidad de ajuste de golpes en todo el tatuaje. Además, es más ergonómico, más fiable y, sobre todo, más rendimiento que su predecesor.
Es una máquina tipo bobina impactante con la confiabilidad y ergonomía de una rotativa.
El enfoque de su diseño es parecerse más a un sombreador/empaquetador que también puede delinear bien, mientras que el Sidewinder es más un delineador que puede sombrear. Si prefiere más golpe a una velocidad más lenta o media, esta es una gran opción. Excelente para línea fina, negro y gris, embalaje de color con cualquier tamaño de mag. Puede impulsar 14 revestimientos, si prefiere "colocar la aguja en la piel", mientras que Sidewinder prefiere que la aguja flote sobre la piel. El Mojobox remasterizado tiene una rueda de carrera ascendente numerada (igual que el V3r) que permite una amplia gama de versatilidad a lo largo del golpe una vez en los rangos de voltaje 5.3 y superiores. Diseñado para agujas estándar. -para cartuchos, puede usar una banda elástica para negar la tensión, aunque no funcionará tan bien como con una aguja estándar. Rango de operación típico: 4 - 6 voltios Peso: 5 onzas
Recientemente remasterizado después de 6 años desde su encarnación, esta es la segunda generación de Mojobox. Ahora con más versatilidad y facilidad de ajuste de golpes en todo el tatuaje. Además, es más ergonómico, más fiable y, sobre todo, más rendimiento que su predecesor.
Es una máquina tipo bobina impactante con la confiabilidad y ergonomía de una rotativa.
El enfoque de su diseño es parecerse más a un sombreador/empaquetador que también puede delinear bien, mientras que el Sidewinder es más un delineador que puede sombrear. Si prefiere más golpe a una velocidad más lenta o media, esta es una gran opción. Excelente para línea fina, negro y gris, embalaje de color con cualquier tamaño de mag. Puede impulsar 14 revestimientos, si prefiere "colocar la aguja en la piel", mientras que Sidewinder prefiere que la aguja flote sobre la piel. El Mojobox remasterizado tiene una rueda de carrera ascendente numerada (igual que el V3r) que permite una amplia gama de versatilidad a lo largo del golpe una vez en los rangos de voltaje 5.3 y superiores. Diseñado para agujas estándar. -para cartuchos, puede usar una banda elástica para negar la tensión, aunque no funcionará tan bien como con una aguja estándar. Rango de operación típico: 4 - 6 voltios Peso: 5 onzas
Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!
Now with more versatility and ease of hit adjustment throughout the tattoo. It is more ergonomic, more reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary.
The focus of its design is to be more like a shader/packer that can also line well, whereas the Sidewinder is more of a liner that can shade. If you prefer more punch at a slower to medium speed, this is a great option. Excellent for fine line, black and grey, color packing with any size mag. Can drive 14 liners, if you prefer to “set the needle into the skin” whereas the Sidewinder prefers to have the needle floated across the skin.
The Remastered Mojobox has a numbered upstroke wheel (same as the V3r) which allows for a wide range of versatility throughout the hit once in the 5.3 and up voltage ranges. Simply turn the stroke wheel for a longer or shorter stroke. The 5 setting is middle of the road and what most people use. Turn up towards 9 for longer srtroke and down towards 1 for shorter stroke.
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive which is the nature of a cartridge.
Typical operating range: 4 - 6 volts, sweet spot for most is 5 Volts on the 5 setting.
Newly remastered, this is the 2nd variant of the 2nd generation of the Mojobox. New spring setup that enhances performance, punch, adjustability, and makes it more cartridge friendly!
Now with more versatility and ease of hit adjustment throughout the tattoo. It is more ergonomic, more reliable, and most of all, more performance focused than its predecessor. It is a punchy coil like machine with the reliability and ergonomics of a rotary.
The focus of its design is to be more like a shader/packer that can also line well, whereas the Sidewinder is more of a liner that can shade. If you prefer more punch at a slower to medium speed, this is a great option. Excellent for fine line, black and grey, color packing with any size mag. Can drive 14 liners, if you prefer to “set the needle into the skin” whereas the Sidewinder prefers to have the needle floated across the skin.
The Remastered Mojobox has a numbered upstroke wheel (same as the V3r) which allows for a wide range of versatility throughout the hit once in the 5.3 and up voltage ranges. Simply turn the stroke wheel for a longer or shorter stroke. The 5 setting is middle of the road and what most people use. Turn up towards 9 for longer srtroke and down towards 1 for shorter stroke.
Intended for standard needle on bar. For cartridges, you may use a rubber band to negate the tension by pulling the rubber band over the top of the armature. Needle on bar will have more hit and cartridges will be slightly subdued and less aggressive which is the nature of a cartridge.
Typical operating range: 4 - 6 volts, sweet spot for most is 5 Volts on the 5 setting.
"The V3/23 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
The 23 model is more reminiscent of the original V3r from 2019, but with some enhancements in the tuning longevity.
We stripped it down a little more, and added in the extra performance. The stroke wheel has been simplified with having 3 timing marks instead of numbers. The marks are of different lengths, with the longest mark signifying the longer stroke range, a middle mark that is the default setting, and a short mark to signify the shorter stroke range.
The sound of the machine has been enhanced in comparison to the 2nd and 3rd variation V3r. Plus the machine now sits a little lower, providing more ergonomics."
Thanks for looking - Dan.
Machine Specs:
Seafoam Powder Coated Brass Frame
Black Motor Cover, DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.
Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Specs:
Steel Frame with durable Black Oxide Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Specs:
Steel Frame with HD Seafoam Powder Coat Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
Step up your tattoo game with the new DK MCi – a plug-and-play remastered version of Dan's Mini Cranker from 2011. Updated and refined, it's designed for precision and ease of use, whether you're using a needle on bar or cartridges. With its wide range of versatility and solid hit, it's a must-have for any tattoo artist.
Specs:
Steel Frame with HD Light Pink Powder Coat Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
Dan Kubin V3/23 Sidewinder - FEATHERWEIGHT Gold x Black CC
Precio habitual$935.00 USD
NEW Dan Kubin V3/23 Sidewinder!
"The V3/23 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
The 23 model is more reminiscent of the original V3r from 2019, but with some enhancements in the tuning longevity.
We stripped it down a little more, and added in the extra performance. The stroke wheel has been simplified with having 3 timing marks instead of numbers. The marks are of different lengths, with the longest mark signifying the longer stroke range, a middle mark that is the default setting, and a short mark to signify the shorter stroke range.
The sound of the machine has been enhanced in comparison to the 2nd and 3rd variation V3r. Plus the machine now sits a little lower, providing more ergonomics."
Thanks for looking - Dan.
Machine Specs:
24k Gold Plated Brass Frame and Motor Cover with Black Hardware (*Finish may vary)
Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.9 ounces
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.
Dan Kubin V3/23 Sidewinder - FEATHERWEIGHT Gold x Black RCA
Precio habitual$870.00 USD
NEW Dan Kubin V3/23 Sidewinder!
"The V3/23 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
The 23 model is more reminiscent of the original V3r from 2019, but with some enhancements in the tuning longevity.
We stripped it down a little more, and added in the extra performance. The stroke wheel has been simplified with having 3 timing marks instead of numbers. The marks are of different lengths, with the longest mark signifying the longer stroke range, a middle mark that is the default setting, and a short mark to signify the shorter stroke range.
The sound of the machine has been enhanced in comparison to the 2nd and 3rd variation V3r. Plus the machine now sits a little lower, providing more ergonomics."
Thanks for looking - Dan.
RCA Specifications:
RCA version is wired for the harder hit mode only using RCA connection. If using a clip cord on this version, they are wired opposite of the standard clip cord version, use Positive side DOWN for hard hit, Positive up for a more muted hit.
This RCA motor housing was designed around a Critical Universal battery pack, but fits with most battery packs I have tried, such as Musotoku, Ink Claw, and Papa.
This will also work good with a right-angle RCA cord.
Clip Cord option still works, it is just wired backwards.
The position of the battery makes the machine’s balance point much more forward, like a pen.
Machine Specs:
24k Gold Plated Brass Frame and Motor Cover with Black Hardware (*Finish may vary)
Featherweight Aluminum version provides the same performance weighing in a couple ounces less than the Brass version at about 3.9 ounces
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.
**Do not connect power to the RCA plug and Clip Cord connection at the same time, it may cause damage to your power supply, battery, and or machine.
Limited Pike x Rogers Slider Rotary - Arco iris verde y dorado
Precio habitual$525.00 USD
Limitado Mike Pike x Cory Rogers Linear Rotary!
Construidas y diseñadas por Cory Rogers y Mike Pike, estas máquinas rotativas lineales colaborativas funcionan sin problemas, son consistentes y están construidas solo con los mejores componentes para garantizar años de uso sin problemas.
Aquí están los detalles:
Cuerpo de aluminio de alta calidad fresado con precisión
Piezas anodizadas verdes personalizadas con marco recubierto de polvo con purpurina arcoíris, además de carpetas y tuerca de mariposa chapadas en oro de 24k
Impulsado por un motor Maxon de primera línea descrito por Mike Pike como el "mejor motor que ha usado en una rotativa"
Cómodo y bien equilibrado con un tornillo de banco que morderá y sujetará todos los tubos desechables y de acero inoxidable
Tuerca de mariposa orientada hacia adelante que no montará su mano ni se interpondrá en su camino
Trazo de 4 mm que funciona muy bien para empaquetado de color, sombreado y también revestimiento de grandes grupos
Empuja de 5 a 49 mag y de 9 a 18 rondas sin problema
Funciona mejor en cualquier lugar entre 5 y 10 voltios.
La mayoría tienen entre 8 y 10 voltios para grupos más grandes, entre 5 y 9 voltios para empaques de color y trabajos en blanco y negro.
Ideal con aguja en barra o cartuchos.
Ligero con un peso de solo 4.5 oz.
Hecho con amor en los EE. UU. por los tatuadores reales Mike Pike y Cory Rogers.
Gracias y disfruta, mike y cory
Workhorse Irons
Limited Mike Pike PMA Direct Drive Rotary - Rosa fuerte x negro
Precio habitual$450.00 USD
¡Nuevo Mike Pike PMA Direct Drive rotativo!
Después de un par de años de ajustes menores y muchas pruebas, ¡el nuevo Mike Pike Direct Drive Rotary finalmente está listo! No necesariamente una reinvención de la rueda, pero aplicando sus años de conocimiento tatuando y construyendo máquinas rotativas, Pike marcó en estos Direct Drives y simplemente hizo un gran funcionamiento rotativo.
Construido utilizando solo los mejores componentes para producir un excelente accionamiento directo integral que funciona sin problemas, consistente y sólido como una roca para años de uso sin problemas. Fabricado con potentes motores de gama alta, una leva ajustable para adaptarse a cualquier carrera, un tornillo de banco de compuerta batiente vertical que garantiza el agarre de los tubos sin problemas y aluminio de primera línea que es liviano y lo suficientemente fuerte como para resistir el paso del tiempo.
- Edición limitada de cuerpos recubiertos de polvo de color rosa fuerte con tapa de motor ennegrecida, tornillo de banco de puerta batiente y herrajes. -Cuerpo de aluminio de alta calidad, marcos y componentes fresados con precisión - Impulsado por un motor Maxon de primera línea descrito por Mike Pike como el "mejor motor que jamás haya usado en un rotativo" - Cómodo y bien equilibrado con un tornillo de banco de tubo de compuerta batiente vertical que morderá y sujetará todos los tubos desechables y de acero inoxidable - Leva de latón ajustable con marcas de referencia de PMA para ayudar a realizar un seguimiento de las configuraciones y ajustes de la carrera. Simplemente afloje el tornillo de fijación de la leva, extraiga la leva interna e insértela nuevamente en una configuración más corta o más larga para cambiar la carrera de forma rápida y sencilla. - Empuja hasta 25 mag y hasta 18 rondas sin problema, aguja en barra o cartuchos - Funciona mejor entre 5 y 10 voltios, dependiendo de lo que presiones y de cómo te tatúes. - Ligero con un peso de tan solo 4.5 oz - Conexión de clipcord
Fabricado con amor en EE. UU. por Mike Pike y sus más de 40 años de experiencia tatuando y construyendo máquinas.
Gracias y disfruta, mike lucio
Workhorse Irons
Dan Kubin Sidewinder V3R de latón negro
Precio habitual$805.00 USD
Dan Kubin V3R Sidewinder
"¡Ahora, con un tornillo de impacto ponderado actualizado! Descubrí que ayuda con la estabilidad del golpe y mejoró el rendimiento general. Además, tenga en cuenta que la posición de la banda elástica es otro elemento de ajuste simple. Para operaciones de menor voltaje o golpe más fuerte, la posición la banda apuntando ligeramente hacia arriba. Esto reducirá la tensión del resorte de retorno, lo que hará que opere mejor a velocidades más lentas y disminuya la cantidad de elasticidad. La bonificación es menos tensión en la banda de goma.
Las actualizaciones anteriores del V3R incluyen agregar el codiciado tornillo de mariposa DK, mover el tornillo de impacto (el elemento de ajuste más crucial e incomprendido) al extremo frontal de la barra de armadura y agregar un pasador de impacto de acero endurecido para que la máquina sea más fácil de reiniciar, y mantendrá su tono mucho más tiempo. También usé algunos trucos del V7 para reducir las salpicaduras y hacer que golpee un poco más rígido en el extremo inferior y también agregué los resortes de respaldo para evitar la rotura del resorte.
Estas actualizaciones se suman a la versión actualizada de 2019, que aún tiene la misma geometría confiable y probada que la v3 original, pero ahora revisada y remasterizada con diferencias sutiles para mejorar el rendimiento general. Este es el Sidewinder más fácil de usar hasta ahora. Las diferencias, además de la estética, son la rueda de carrera numerada, una marca de sincronización del tornillo de impacto en la leva y el marco (como el v5-6). Además, hice una nueva configuración de bloqueo de tornillo de banco con resorte que sujeta el tubo sin esfuerzo. La rueda de carrera está indexada en 10 posiciones y numerada en consecuencia".
Gracias por mirar - Dan.
Especificaciones de la máquina:
Marco de latón de óxido negro con herrajes negros (*El acabado puede variar)
Tornillo de mariposa DK, nueva barra de armadura y rueda de carrera actualizada para mejorar el rendimiento
El renombrado forro rotativo. Hunde sin esfuerzo líneas de cualquier tamaño con solo rozar la piel.
El motor es el mismo que el Sidewinder V2-V4, que ha probado la prueba del tiempo. Ha sido uno de los favoritos de los coleccionistas de Sidewinder desde hace mucho tiempo.
Vice-Lock que se aprieta fácilmente en casi cualquier tubo
Ideal para todas las variedades de Line Work o como Fast Shader/Packer
Marca de sincronización en la leva y el marco para ajustar el tornillo de impacto. (Al igual que el V5 y V6)
Dial de trazo numerado para que puedas jugar fácilmente con el trazo sin temor a perder ese punto óptimo. No puedes hacerlo demasiado largo o demasiado corto
Configuración de la máquina:
Aguja estándar en la barra: envuelva una banda elástica gruesa alrededor de la tapa del motor y en la parte delantera de la máquina para aumentar la tensión de la barra de agujas. Se recomienda utilizar bandas elásticas gruesas y pezones perfectos de Dan.
Cartuchos: envuelva una banda elástica alrededor de la tapa del motor y sobre la parte superior de la barra de la armadura para contrarrestar la tensión hacia arriba del cartucho. Tanto las bandas de goma gruesas como las estándar funcionan, solo dependerá de la tensión de la membrana o la banda del cartucho para determinar si la banda de goma proporciona la contrarresistencia adecuada.
*Totalmente oxidado en negro. *Tenga en cuenta que el latón alcanzará su punto máximo con el tiempo donde se ve muy desgastado, lo que se suma a su carácter.
Para obtener más información, mire el video de configuración y ajuste de V3R:
