"¡Ahora, con un tornillo de impacto ponderado actualizado! Descubrí que ayuda con la estabilidad del golpe y mejoró el rendimiento general. Además, tenga en cuenta que la posición de la banda elástica es otro elemento de ajuste simple. Para operaciones de menor voltaje o golpe más fuerte, la posición la banda apuntando ligeramente hacia arriba. Esto reducirá la tensión del resorte de retorno, lo que hará que opere mejor a velocidades más lentas y disminuya la cantidad de elasticidad. La bonificación es menos tensión en la banda de goma.
Las actualizaciones anteriores del V3R incluyen agregar el codiciado tornillo de mariposa DK, mover el tornillo de impacto (el elemento de ajuste más crucial e incomprendido) al extremo frontal de la barra de armadura y agregar un pasador de impacto de acero endurecido para que la máquina sea más fácil de reiniciar, y mantendrá su tono mucho más tiempo. También usé algunos trucos del V7 para reducir las salpicaduras y hacer que golpee un poco más rígido en el extremo inferior y también agregué los resortes de respaldo para evitar la rotura del resorte.
Estas actualizaciones se suman a la versión actualizada de 2019, que aún tiene la misma geometría confiable y probada que la v3 original, pero ahora revisada y remasterizada con diferencias sutiles para mejorar el rendimiento general. Este es el Sidewinder más fácil de usar hasta ahora. Las diferencias, además de la estética, son la rueda de carrera numerada, una marca de sincronización del tornillo de impacto en la leva y el marco (como el v5-6). Además, hice una nueva configuración de bloqueo de tornillo de banco con resorte que sujeta el tubo sin esfuerzo. La rueda de carrera está indexada en 10 posiciones y numerada en consecuencia".
Gracias por mirar - Dan.
Especificaciones de la máquina:
Marco de latón de óxido negro con herrajes negros (*El acabado puede variar)
Tornillo de mariposa DK, nueva barra de armadura y rueda de carrera actualizada para mejorar el rendimiento
El renombrado forro rotativo. Hunde sin esfuerzo líneas de cualquier tamaño con solo rozar la piel.
El motor es el mismo que el Sidewinder V2-V4, que ha probado la prueba del tiempo. Ha sido uno de los favoritos de los coleccionistas de Sidewinder desde hace mucho tiempo.
Vice-Lock que se aprieta fácilmente en casi cualquier tubo
Ideal para todas las variedades de Line Work o como Fast Shader/Packer
Marca de sincronización en la leva y el marco para ajustar el tornillo de impacto. (Al igual que el V5 y V6)
Dial de trazo numerado para que puedas jugar fácilmente con el trazo sin temor a perder ese punto óptimo. No puedes hacerlo demasiado largo o demasiado corto
Configuración de la máquina:
Aguja estándar en la barra: envuelva una banda elástica gruesa alrededor de la tapa del motor y en la parte delantera de la máquina para aumentar la tensión de la barra de agujas. Se recomienda utilizar bandas elásticas gruesas y pezones perfectos de Dan.
Cartuchos: envuelva una banda elástica alrededor de la tapa del motor y sobre la parte superior de la barra de la armadura para contrarrestar la tensión hacia arriba del cartucho. Tanto las bandas de goma gruesas como las estándar funcionan, solo dependerá de la tensión de la membrana o la banda del cartucho para determinar si la banda de goma proporciona la contrarresistencia adecuada.
*Totalmente oxidado en negro. *Tenga en cuenta que el latón alcanzará su punto máximo con el tiempo donde se ve muy desgastado, lo que se suma a su carácter.
Para obtener más información, mire el video de configuración y ajuste de V3R:
¡Aquí tienes! He hecho mi diligencia debida para obtener un GRUESO duradero, de ultra alta calidad y personalizado. CULO. GOMA. Bandas
Hecho en EE.UU. ¡100, 250 y 1300 unidades disponibles!
- Dan
Workhorse Irons
Dan Kubin MCi - Black
Precio habitual$750.00 USD
NEW Dan Kubin MCi (Mini Cranker with Impact)!
New machine from Dan Kubin! The MCi is a tribute Dan has made to his old Mini Cranker model from years ago. Revised and updated with impact screw added for more snap at the tip, a better motor, and improved geometry. MCi machines are a plug and play DK option with a wide range of versatility and a solid hit in a simpler and smoother setup.
Specs:
Steel Frame with durable Black Oxide Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
New machine from Dan Kubin! The MCi is a tribute Dan has made to his old Mini Cranker model from years ago. Revised and updated with impact screw added for more snap at the tip, a better motor, and improved geometry. MCi machines are a plug and play DK option with a wide range of versatility and a solid hit in a simpler and smoother setup.
Specs:
Steel Frame with HD Light Pink Powder Coat Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
New machine from Dan Kubin! The MCi is a tribute Dan has made to his old Mini Cranker model from years ago. Revised and updated with impact screw added for more snap at the tip, a better motor, and improved geometry. MCi machines are a plug and play DK option with a wide range of versatility and a solid hit in a simpler and smoother setup.
Specs:
Steel Frame with HD Seafoam Powder Coat Finish
Weighted Brass Armature
Deluxe Kubin Components including DK Thumbs and updated Slide Vise
Setup / Usage:
Works well with Standard Needle on Bar AND with Cartridges
Possible to run with Cartridges without any adjustment or tricks, but if you pull your rubber band over the armature it will increase the snap at the tip
This machine is cartridge friendly, but best to use lower tension cartridges if going that route. (Workhorse Eco Carts and Non Membrane Carts work well with these machines)
Great for Lining and Shading with small to medium groupings, turn voltage up and down for speed and hit adjustment as needed
Higher voltage between 5 - 7 Volts for most Lining
Lower Voltage between 3.5 - 5 Volts for most Shading, Color Packing, and Stipple Work
Polarity is not crucial, but will run slightly more efficiently with Positive Down
The impact screw can be backed off all the way, but ideal to still have a little impact to reduce motor shaft strain
Turning the impact screw in too much will result in stalling the machine or putting too much strain on the motor.
Ideal impact is about 1/4-1/2 turn clockwise from the point of zero impact.
Use and Care:
Please refer to the MCi setup video on my YouTube channel for further clarification - See Link Below
After a few years, the bearings may dry up. You may use A SINGLE DROP of sewing machine oil on the bearings. DO NOT FILL THE MOTOR WITH OIL!!
Keep sterilants away from all moving and electrical components!
Sterilants are corrosive and will damage your machine if used carelessly.
"The V3/23 follows the same concept as the past V3r, but with a focus on what makes a Sidewinder a Sidewinder. Hard hitting, effortless, and zippy. -Intended for experienced artists who don’t want to mess around.
The 23 model is more reminiscent of the original V3r from 2019, but with some enhancements in the tuning longevity.
We stripped it down a little more, and added in the extra performance. The stroke wheel has been simplified with having 3 timing marks instead of numbers. The marks are of different lengths, with the longest mark signifying the longer stroke range, a middle mark that is the default setting, and a short mark to signify the shorter stroke range.
The sound of the machine has been enhanced in comparison to the 2nd and 3rd variation V3r. Plus the machine now sits a little lower, providing more ergonomics."
Thanks for looking - Dan.
Machine Specs:
HD Pink Powder Coated Brass Frame with 24k Gold Plated Hardware and Motor Cover
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 and V7 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Marked stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
V3R and V3/23 Sidewinders are engineered, designed, and tested by Dan, milled in his most trusted machine shop in Kansas City, then built by DK certified trained technicians at the Workhorse facility in Michigan. All other models are built by Dan and his team in Kansas City. V3/23s go through rigorous QC checks and are all ran through our testing machine to lightly break in. One year warranty on all models. V3R and V3/23 are serviced by Workhorse, all others are serviced by Dan or one of his certified technicians found on his website.