"Now with an updated weighted impact screw! I found that it helps with the stability of the hit, and improved overall performance. Also, please note the rubber band position is another simple tuning element. For lower volt operations, or harder hit, position the band pointing slightly up. This will reduce return spring tension thus making it operate better at slower speeds and decreasing the amount of give. Bonus is less strain on the rubber band.
Previous updates to the V3R include adding the coveted DK thumbscrew, moving the impact screw (the most crucial and misunderstood tuning element) to the front end of the armature bar and added a hardened steel impact pin so the machine will be easier to reset, and will hold its tune much longer. I also used a few tricks from the V7 to reduce spitting and make it hit a bit more rigid on the low end and added the backer springs as well to prevent spring breakage.
These updates are in addition to the 2019 updated version which still has the same dependable and proven geometry as the original v3, but now revisited and remastered with subtle differences to improve overall performance. This is the most user friendly Sidewinder yet. The differences, others than aesthetics, is the numbered stroke wheel, an impact screw timing mark on the cam and frame (like the v5-6). Additionally, I did a new spring loaded vice lock setup that effortlessly clamps down your tube. The stroke wheel is indexed in 10 positions, and numbered accordingly."
Thanks for looking - Dan.
Machine Specs:
Black Oxide Brass Frame with Black Hardware(*Finish may vary)
DK Thumbscrew, new Armature Bar, and updated Stroke Wheel for improved performance
The renowned rotary liner. Effortlessly sink any size line by just grazing the skin.
The motor is the same as the V2-V4 Sidewinder, which has proven the test of time. It has been a favorite of the long time Sidewinder collectors.
Vice-Lock that easily tightens on nearly any tube
Great for all varieties of Line Work or as a Fast Shader/Packer
Timing mark on the cam and frame for setting the impact screw. (Just like the V5 and V6)
Numbered stroke dial so you can easily play with the stroke without fear of losing that sweet spot. You can’t make it too long or too short
Machine Setup:
Standard Needle on Bar: wrap a thick rubber band around the motor cap and across the front of the machine to add needle bar tension. It is recommended that you use Thick Rubber Bands and Dan's Perfect Nipples.
Cartridges: wrap a rubber band around the motor cap and over the top of the armature bar to counteract the cartridge's upward tension. Thick or standard rubber bands both work, it will just depend on the tension of the cartridge membrane or band to determine with rubber band provides the proper counter resistance.
*Completely black oxided. *please note that the brass will peak though over time where it sees heavy wear, adding to its character.
For more info please watch the V3R Setup and Tuning Video:
The most significant update to the V3/24 Sidewinder is the added (and optional) Needle Bar Tensioner. This added Tensioner eliminates the need to use a Rubber Band, improving all around machine performance and results. Tensioner reduces spitting and increases power.
The V3/24 Tensioner can be used on all versions of Dan Kubin V3Rs, 2019 to 2024.
Needle Bar Tensioner Specifications:
Lightweight Aerospace Aluminum Arm with precision made custom bearing
Creates necessary needle bar tension for stability, eliminating the need to use a Rubber Band
Moves forward and backwards, in and out of position easily by loosening and tightening the thumbscrew
When setting up your needle and tube, position Needle Tensioner in desired position depending on the amount of tension you want to add to the needle bar.
Adjust position by loosening the thumbscrew, pull arm back and then tighten when you reach desired tension.
Upgrade Step by Step:
Loosen and remove the thumbscrew
Insert thumbscrew into hole in Needle Bar Tensioner
Re-insert thumbscrew into frame with Tensioner bearing facing inwards (see picture)
Ensure Vise Slide is in correct position, so the thumbscrew easily threads into Slide
Tighten with Needle Bar Tensioner in desired position
**OG V3R and V3/23 SPECIAL NOTE - Use of this Tensioner instead of Rubber Bands will noticeably increase the strength of your machine. If it is hitting too hard using the Needle Bar Tensioner, simply adjust your voltage and turn the machine down and adjust stroke wheel setting as needed to accomplish desired speed / hit.
